I taught (teach) several aspects of "green woodworking" and related subjects, so I love your question. The buying and using of old tools is great...no matter the source. However, I have seen much frustration ensue over getting them adjusted, and "work ready." As often a beginner with limited budgets, also have limited traditional skill sets as well in understanding these tools and sharpening them. You must be patient with yourself, as tuning these old tools up will be very time consuming. Sharpening (and the proper tools of sharpening) should be your first acquisition. So many folks buy chickens before building a proper "chicken coop." Traditional tools are the same way, as there is no reason to own them, if you can't keep them properly honed.

If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.
YouTube is a great place to watch DIY woodworking tutorials that give you visual walkthroughs on how to do woodworking projects from start to finish. YouTube videos can inspire you to experiment with new ideas and try out projects you had never dreamed of yourself. With 20 channels dedicated to bringing you new project ideas and even showing you how to do them, you will have plenty of projects to ponder. So it's time to open your scrap wood cabinet and get started on something new.
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.

We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  

We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
About Youtuber Chop With Chris YouTube channel is focused on educational and entertaining "How To" woodworking videos using just hand tools. My DIY content covers a wide range of projects and plans from tables and chairs to foot powered machines, bows, arrows, crossbows and other related bushcraft videos as well as tool eduction. I am a maker and have a passion to share my knowledge with others.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.

Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.

Carpenters Builders Pencils 13pc Joiners Sharpener Soft-lead oval-section carpenters pencils for marking timber, brick, stone and other building materials. Draws thick or thin lines on both rough and smooth surfaces. Oval-shaped length means pencils do not roll away when placed on inclined surfaces. Includes 12 pencils and a sharpener. Pencils supplied are in BLUE.
I just do it. Lol. Most of my projects are for my wife so its easier to scrape money together then listen to complaints about them not getting done! Seriously though, its tough. I have two expensive hobbies......woodworking and bass fishing, latter of the two being the worst. I reserve all my side work money for the two. One thing that helps is owning our own saw mill, lumber is basically free other then time.
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
Another option is to use two small clamps to hold two boards in place, and then wedge the wood pieces, that you’re trying to glue, in between them. I’ve found that this works better than the ratchet straps when trying to glue up thinner lumber, like boards from old pallets. When using this method, you should have the wood on a completely flat surface, and often it helps to put some weight on top to keep it from bowing.
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Birch is readily available and less expensive than many other hardwoods. Birch is stable and easy to work with. However, it’s hard to stain because it can get blotchy, so it is generally preferred to paint Birch.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required): 

For many tasks you may not gain much benefit from going above 4-500 grit but polishing your axe to 0.33 micron certainly won’t affect edge retention. For finishing work, you certainly do want as well polished of an edge as possible since that means less scraping or sanding. A well honed plane can leave a surface that’s actually too smooth for painting.
Oak is one of the most widely used and respected hardwoods in furniture making. Available in two varieties — red and white — oak is very strong and also quite heavy. White oak is sometimes preferred for furniture making because it has a slightly more attractive figure than red oak, but either variety can give you a beautiful finish that stains very well. Oak can be used for almost any woodworking purpose, and is an excellent choice for pieces that will last a lifetime – literally! As they say, it is “solid as oak”!
I moved back to my small hometown just a few years later.  Had a stable income, now with my own home with a shop.  That’s were I started getting back into woodworking.  I have been doing it now on a steady basis for the last ten years or so.  I do it just for a hobby, but I enjoy doing it to pass the time or to try and make a new piece of furniture.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!    

As Chief Creative Officer and Founding Partner at Brit + Co, Anjelika Temple brings her voracious consumption of all things creative and colorful to DIY projects, geeky gadgetry finds and more. When she's not DIY-ing her heart out, you'll find her throwing dinner parties with friends or adventuring with her husband David, their daughter Anokhi, and their silly dog Turkey.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!

Frank Howarth is a unique guy - educated as an architect, but with practical woodworking skills to rival any journeyman.  He has the most enviable workshop of anybody I've seen, and his projects are aspirational on every level - creativity, originality, ingenuity, and craftsmanship.  He devotes a lot of time to talking about the layout and design of his ever-changing workshop, and there's a lot of clever ideas to steal and pass off as your own.   If you can't tell, I love Frank.  Oh, and his stopmotion videos are awesome. 
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
There are some basic things every woodworker needs to get started. Assuming you aren't the kind of person that does everything with hand tools, you'll first need a drill. Power drills come in many different styles and price ranges. The popular trend right now is for companies to make cordless tool systems that all run off of the same battery packs, and a drill is often the first tool a person gets in the set. Cordless drills are popular and handy for doing household tasks , such as hanging picture frames; but for serious woodworking, they can lack power and might die in the middle of a job. Corded drills are a less expensive option and often work better for the tasks you'll be doing in a wood shop; just get a cheap extension cord to go with it. You can easily find a corded drill of good quality for about $100.
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday. 

Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
Over a year ago, I wrote up a round-up of three woodworking resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Few things are as satisfying and relaxing as making something new with your own hands. Programming comes close, at least for me (and I've recently offered some tips on learning to code), but it's still... Read More which included talented YouTube woodworkers Matthias Wandel, Steve Ramsey, and Marc Spagnuolo, AKA The Wood Whisperer. All three still produce wonderful work — and today I’d like to introduce you to five other YouTube woodworking channels worth following.
About Youtuber Chop With Chris YouTube channel is focused on educational and entertaining "How To" woodworking videos using just hand tools. My DIY content covers a wide range of projects and plans from tables and chairs to foot powered machines, bows, arrows, crossbows and other related bushcraft videos as well as tool eduction. I am a maker and have a passion to share my knowledge with others.
Arbortech Turbo Plane – The turbo plane is more than 7 times the cost of the Bad Blade Carver, however The turbo plane is kind of a more refined animal.  It probably isn’t fair to compare the two. The Turbo Plane leaves a better finish and can be used in a different way,  but for bulk removal and heavy shaping, I think the Bad Blade Carver wins. If you want the scalloped and smooth surface, then the Turbo Plane wins.
I’m going to find a different piece of metal, and I’ll post a video of the working track when it’s done. I bet some of you are coming to expect failure from this blog. I warned you in the beginning that I’m new to this. I’m trying to share my experience from both my successes and my failures. It just so happens that I have a lot more failures so far.
×