I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key storage, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws. Because of this, I'd stick to the two saws we looked at in the $500 build: The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110. These two additions bring our running total to just over $500.
My name is Marc Spagnuolo and welcome to my channel. I am a podcaster, video producer, author, and woodworking enthusiast. I have contributed articles and video content to FineWoodworking.com, Popular Woodworking Magazine and WOOD Magazine. Producing the Wood Whisperer is a great way for me to combine four of my passions: woodworking, technology, education, and humor. I believe that even the most complicated woodworking project is just a series of steps. My goal with this channel is to show you the tools and techniques you need to perform those steps.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
If you'd like to learn more about the differences between hardwood species, I can think of no better resource than R. Bruce Hoadley's 1980 masterpiece, Understanding Wood: A Craftsman's Guide to Wood Technology. Not only does Hoadley detail nearly every species used for woodworking, he does an exceptional job at describing how to prepare, work with and finish these hardwoods. This is an industry-standard resource, one that I'd highly recommend to every woodworker.
Assume that there aren’t any decent tools on craigslist or at garage sales, and keep in mind that I have absolutely no tools, dust collection, shop-vac, clamps, sanding & painting accessories, tables, materials to build my own tables/stands/jigs, or anything else—not even safety gear (you’re such a good buddy that you even let me borrow your extra set of goggles and your earmuffs when I used to come over).
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap. ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15). 1 rip handsaw (used ones can be found at Antique stores for $20 or less. Try to find one that is fairly sharp to start with). Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both). A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
If you choose paint for your finish, you won't want to waste your money on woods known for their color and beauty when stained, so avoid richly-colored species such as oak, maple, walnut or mahogany. For painted projects, poplar is a very good choice because it is relatively stable and takes paint quite well (not to mention that it doesn't look all that good stained).
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
Oak is one of the most widely used and respected hardwoods in furniture making. Available in two varieties — red and white — oak is very strong and also quite heavy. White oak is sometimes preferred for furniture making because it has a slightly more attractive figure than red oak, but either variety can give you a beautiful finish that stains very well. Oak can be used for almost any woodworking purpose, and is an excellent choice for pieces that will last a lifetime – literally! As they say, it is “solid as oak”!
About Youtuber This channel is created to share my passion for woodworking and guide beginners into realizing the joy of this hobby. Woodworking is fun, inspiring and helps you to design, create and relax. You can pick up a piece of wood and create something out of it and the result is uplifting. You just created something valuable from piece of wood.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ... More + Product Details Close
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, similar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.