About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.  

Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.

Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
What tools are needed to start woodworking? Well, this list can vary greatly depending on your budget. The best beginner woodworking tools are subjective but can vary largely depending on how much money you are willing or able to invest to start out in woodworking. It can also vary depending on if you are wanting to start out woodworking just as a hobby or as a side-hustle business. Most of the best beginner woodworking tools on this list are either tools I own, have owned, or at least have used in the past.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
There are and they are considerably cheaper. I found a pair of glue brushes on Amazon for less than half the price of a singles dedicated glue brush. I tested them out on a recent gluing and they work well for spreading glue and getting it into dovetails and mortises. When you are done you can either run the brush underwater to clean it or wait until the glue dries the pluck it off the bristles with a few easy pulls. The glue comes right off the silicone bristles.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.
For those who want to make money from their woodworking skills, David Piccuito's channel Make Something is a great place to start. He encourages woodworkers to use his designs for selling to clients as long as he gets credit for the design. Make Something has tutorials for making things at any skill level, from beginner to expert. It is filled with woodworking hacks on things like how to make curved inlays and how to drill really large holes—even those holes that are larger than your largest bit.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.

Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 

The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
Just how small?  Will you have an extra bedroom for your shop or will you be doing woodworking in your living room?  Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time?  A while back FWW had a video tour of a shop in Japan that was smaller than small.  I'll try to find it and get back.  Found it...  shows what can be done in a small space but this shop was not on a small budget so no help there.
Just how small?  Will you have an extra bedroom for your shop or will you be doing woodworking in your living room?  Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time?  A while back FWW had a video tour of a shop in Japan that was smaller than small.  I'll try to find it and get back.  Found it...  shows what can be done in a small space but this shop was not on a small budget so no help there.
I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate.  So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it.  I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.
On the money issue one`thing I did is find something that is fairly easy to make and easy to sell. I made kaleidoscopes to begin with and still whip up a batch if I need to buy wood or a new tool. A neighbor WW makes wooden condiment holders for restaurants. A good friends son worked his way thru college by making a certain bearing that they needed on his tiny lathe. Spend a month or so on $$$ stuff before doing the better stuff.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
This unique approach to woodworking was expressed by George Nakashima’s work throughout the mid-20th century. He became known for leaving the natural, or live edge of the wood in tact as part of the finished piece. The profile of this live edge reflects the curvatures and unique textures of the tree’s exterior silhouette, assuring that no two pieces are ever the same. The use of this wood creates a bold, artistic and natural feel that is an extremely interesting way of obtaining that “wow factor” in a piece.
about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!

As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers. 

If you are just getting started in woodworking and want to know what tools you’ll need to set up shop, you’ll want to download this free PDF from Popular Woodworking. We have put together a complete list of basic woodworking tools to kick-start your new hobby. In this free download, you’ll get our recommendations for the best hand and power tools for beginners. Buy these tools and you’ll have everything you need to make great woodworking projects.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
×