When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time. It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years. During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools. It is sort of an inexpensive crash course in hand tools. Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read. Use the internet to learn all you can about a tool before buying. The tools you need are dictated by what you want to build.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
YouTube is a great place to watch DIY woodworking tutorials that give you visual walkthroughs on how to do woodworking projects from start to finish. YouTube videos can inspire you to experiment with new ideas and try out projects you had never dreamed of yourself. With 20 channels dedicated to bringing you new project ideas and even showing you how to do them, you will have plenty of projects to ponder. So it's time to open your scrap wood cabinet and get started on something new.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate. So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it. I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.
First, let's dump that hand powered saw/miter box. It gets the job done, but it takes forever. We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense. This won't be your forever saw, but it should do fine for most projects. It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to purchase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very reasonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do anything I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching.
Another staple in the beginner woodworkers tool kit has to be the cordless drill. Used for either drilling holes or driving fasteners, this tool gets used on almost every project. There a tons of options here regarding size of batteries, aka power, but something around the 18-20 volt range is a good all-around size that will not leave you constantly wishing you had something larger or smaller. Here is a large accessory kit at a good price that should give you most of the drivers a bits you will need.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Let's talk about a few strategies for building out your shop below retail price. There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss. First of all, not everyone lives in an area where these avenues exist. Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand. Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Thanks for the suggestion. At this point my plan is to focus on keeping things as they are. Many people have stated that they appreciate the current format. The videos are not necessarily intended for everyone, however they are for people that have a curiosity and a desire to learn woodworking. These are the people that will watch and raise questions and then ask the questions.
The solution to potentially wedged boards on a jointer is to add a planer to the mix. A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface. This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square. As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.
I Like to Make Stuff is the perfect channel for beginners who want comprehensive teaching on woodworking. It has a show called Maker 101 that goes into the basic skills you need to start making stuff. I Like to Make Stuff is not intimidating to the beginner because it isnâ€™t afraid of showing woodworkers making mistakes on their project rather than always doing everything perfectly.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )