Even the backside grinding shown in the single frame of the video shows the effects of hand held sharpening. There is a curve on the flat side of the blade! Starting to look like a spoon. It’s impossible to get a flat surface when using bones and tendons. This effect was exploited to make the first lens when done in glass. Telescope mirror grinders do it too using two different hardness of glass, if machine done it would be flat. If those “slate” tiles are flat they must be ground flat not baked. No need to check.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close

About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.  

Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table. 

The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.

Danish Oil is an oil-based finish that soaks deep into wood pores to provide protection from the inside out. Generally made from a unique blend of penetrating oil and varnish that stains, seals and protects all at the same time, it enhances the natural look and feel of the wood, and creates the rich, warm glow. This finish is ideal for furniture, trim, molding or any other bare wood interior surface that calls for an accentuated look.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.

In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.
If you choose paint for your finish, you won't want to waste your money on woods known for their color and beauty when stained, so avoid richly-colored species such as oak, maple, walnut or mahogany. For painted projects, poplar is a very good choice because it is relatively stable and takes paint quite well (not to mention that it doesn't look all that good stained).
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools.  It is sort of an inexpensive crash course in hand tools.  Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read.  Use the internet to learn all you can about a tool before buying.  The tools you need are dictated by what you want to build.
What tools are needed to start woodworking? Well, this list can vary greatly depending on your budget. The best beginner woodworking tools are subjective but can vary largely depending on how much money you are willing or able to invest to start out in woodworking. It can also vary depending on if you are wanting to start out woodworking just as a hobby or as a side-hustle business. Most of the best beginner woodworking tools on this list are either tools I own, have owned, or at least have used in the past.
Teak is an excellent choice, the “crème de la crème”, for fine outdoor furniture. Teak is highly weather-resistant by nature, which means that it does not have to be weatherproofed when used outdoors – although it often is finished and stained for aesthetic purposes. Teak is one of the most expensive exotic hardwoods there are, but it will look absolutely beautiful and maintain its integrity over time.
By the way, before you yell at me about the fact that the price on the links for the nail gun is more than $200, listen up I have a handy tip:  There are sales throughout the year on this exact package for $200.  That’s how I bought mine.  Just keep checking back.  And be sure to follow me on social media.  I keep checking it, too and if I see it’s on sale, I will post it to let you all know!

The most common type of cedar used today is the Western Red variety. Western Red Cedar, as its name implies, has a reddish color to it. This type of wood is relatively soft, has a straight grain, and has wonderful aromatics. Western Red cedar is mostly used for outdoor projects such as furniture, decks, signs and exterior siding because it is naturally resistant to moisture and water corrosion. Cedar also makes for a great closet or chest for storing clothes and other fabrics because of its resistance to moisture. Cedar is moderately priced and can be stained to a variety of tones.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close

That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE
I’m going to find a different piece of metal, and I’ll post a video of the working track when it’s done. I bet some of you are coming to expect failure from this blog. I warned you in the beginning that I’m new to this. I’m trying to share my experience from both my successes and my failures. It just so happens that I have a lot more failures so far.
Improving an item with a Resin increases the effective item level by 3. For example, a white quality Oak Bow at level 16 will, once improved with Pitch, have an effective item level of 19. Improving it again with Turpen, will make the effective item level 22. You will notice in the Weapon and Armor tables that the Superior value at level 16 is the same as Normal at level 22. This is important to note, since several Crafted Sets have break points where their bonuses increase based upon "effective level".
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.

Carl Jacobson has created over 350 videos to overwhelm you with project ideas, some of which you can complete in less than an hour. He takes you through the entire process from preparing the wood to the sanding and finishing of the project. Carl releases a new video every Friday with a follow-up video every Monday to answer questions based on the feedback he received over the weekend.


This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
I moved back to my small hometown just a few years later.  Had a stable income, now with my own home with a shop.  That’s were I started getting back into woodworking.  I have been doing it now on a steady basis for the last ten years or so.  I do it just for a hobby, but I enjoy doing it to pass the time or to try and make a new piece of furniture.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!   

If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
Add a little rustic décor to your walls by building a wooden mail sorter. Not only does this give you beautiful rustic décor, it also serves a very handy function by keeping mail neatly organized. You just need a few pieces of wood and some small coat hooks at the bottom to hang your keys. Stain it in any color you want and you have a very functional and very beautiful sorter.
It's funny how some interests (or trades) got onto YouTube very early.  Woodworking has been popular on there since the video-sharing behemoth got started.  I suspect this is because the US has a strong tradition of TV shows about woodworking - two great examples being Norm Abram's New Yankee Workshop and Roy Underhill's Woodwright Shop.  With a plethora of channels available on cable, and a bigger population, broadcasters were able to air more niche, and thus detailed shows.   Over in the UK we had four channels, and so if something wasn't going to appeal to at least 5% of the population (or it was cultural) then it didn't stand a chance.   

I started Woodworking Wednesdays because I thought my woodworking projects didn’t fit in very well with my UnbrokenFurniture.com blog. However, more and more, the furniture I’m making on that blog is handmade reclaimed wood furniture. This has sort of made this blog redundant. I’m not putting out enough furniture pieces to populate both blogs, so I’m going to stop posting those here.


A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
For many tasks you may not gain much benefit from going above 4-500 grit but polishing your axe to 0.33 micron certainly won’t affect edge retention. For finishing work, you certainly do want as well polished of an edge as possible since that means less scraping or sanding. A well honed plane can leave a surface that’s actually too smooth for painting.
About Youtuber Woodworking is my passion and I there is nothing I won't try to build, fix, or improve on my own. I got into woodworking and the passion has completely consumed me. Becoming a great woodworker and do it yourself-er is about finding the right information and creative solutions with the materials and skill sets available to you. I eagerly look forward to showing you how I accomplish my projects.
Right now you're thinking, "but the plans say to use a table saw for this." That's OK , because the great thing about a circular saw is you can turn it into a table saw. There are plenty of videos online showing how to do this, but you are essentially cutting a slot in a piece of plywood, mounting the circular saw to it, and flipping it over. With careful planning you can have a good basic table saw without spending hundreds of dollars, and it can come apart if you need to save space. With that setup you can cut long pieces of wood that you may not be able to brace properly to cut with the circular saw. You can also make more accurate cuts than by holding the circular saw. It can also be used to cut simple dados and to cut a bevel. You do need to be careful, as it won't have the blade guard covering the saw blade anymore.

While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.


When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Swap meets and flea markets? Often you see people bring all the old tools out of their garage that grandpa handed down to them and that haven't seen any use for 40 years. Hand saws, chisels, planes, drills, and all other manner of hand tools that are hard to give away because most people can't even tell what they are. An old fashioned brace-and-bit falls into that category, and all the people want for it is a couple of bucks.
One of the most heavily used tools in your shop will be your table saw.  It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs.  Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.  
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
If you want to do any amount of bowl carving or other types of carving that will require removal of large amounts of stock, I can't recommend an angle grinder and chainsaw-tooth wheel in place of the abrasive wheel. I've used the Arbortech brand, but there are a few different brands and style available. I'm sure you could buy a used grinder for $20 or so.
If you want to do any amount of bowl carving or other types of carving that will require removal of large amounts of stock, I can't recommend an angle grinder and chainsaw-tooth wheel in place of the abrasive wheel. I've used the Arbortech brand, but there are a few different brands and style available. I'm sure you could buy a used grinder for $20 or so.
When I bought my miter saw, I didn’t buy the cheapest, but I didn’t want to spend a ton of money. I started out with a small Hitachi.  I LOVE my saw and it does a great job—I have no complaints.  However, I do kind of wish I had gotten a larger one.  Here’s the thing.  I can cut up to a 1×6 board in one pass on my miter saw.  But if I cut any larger than that, I have to flip the board over and cut again from the other side.  That means if I’m making something from 1x8s or wider, I have to make twice as many cuts.  Sometimes this is a pain.  But it’s obviously not a big enough pain for me to spend the extra money to go buy a bigger one haha.  Just something to consider. Either way, a miter saw of any size is guaranteed to be a good investment.  Also, watch out for sales on this saw…it’s often listed on sale for $100 (that’s how I got mine!).
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs. 
×