We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
As an x aerospace machinist I have run manual lathes and mills and programmed and run CNC as well. IMO a manual lathe is far more versatile and useful than a CNC for the average DIY buff. A CaN C is basically a very accurate production machine but to spend time programming, setting up, proving out just for a couple or several pieces is not practical ( unless you have money and time to spare)
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
About Youtuber On this channel I will try to share my passion for wood and the skills and experience gained in the furniture carpentry business for almost 30 years. I will try to help solve the problems caused by the processing of wood and other furniture materials. When designing and fabricating furniture as well as I will try to tell you how to run your own business.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
I moved back to my small hometown just a few years later. Had a stable income, now with my own home with a shop. That’s were I started getting back into woodworking. I have been doing it now on a steady basis for the last ten years or so. I do it just for a hobby, but I enjoy doing it to pass the time or to try and make a new piece of furniture.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
"Plaintiff never complained of discrimination to the on site owners. Moreover, Wirths invested a great deal of their personal time counseling Plaintiff to become a successful supervisor and Plaintiff never complained of difficulties with her direct supervisor even though Woodworker's Supply had and enforced (1) an antidiscrimination policy, and (2) a mandatory requirement to immediately report all incidents of discrimination."
Kids love DIY projects, especially when they get to give those projects away as gifts. You can help your little ones to make a great picture frame for Father’s Day with just a few twigs and a hot glue gun. Just glue the twigs to the frame and let the kids decorate however they want. Use burlap for the matting and add a special message with a Sharpie.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
The last tool I recommend for every beginning woodworker is a quality router. While many routers available today offer two different bases (a stationary base and a plunge router base), for most beginners, a quality stationary base model will take care of quite a number of tasks, and can also be mounted in a router table should you choose to invest in (or even build one) one down the line. Choose a router model that is at least 2-HP and has electronic variable speed controls (as larger cutting bits should use slower speeds), a soft start mechanism and is easy to make bit changes (preferably with the ability to use both 1/2-inch and 1/4-inch shank router bits).