After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap.  ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15).  1 rip handsaw (used ones can be found at Antique stores for $20 or less.  Try to find one that is fairly sharp to start with).  Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both).  A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Birch is readily available and less expensive than many other hardwoods. Birch is stable and easy to work with. However, it’s hard to stain because it can get blotchy, so it is generally preferred to paint Birch.
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
About Youtuber Steve Johnson is a full time life-long hobbyist woodworker committed to helping new and experienced woodworkers achieve the "shop of their dreams" - even if (especially if?) they don't have a dream budget to work withHis videos can be seen at "DownToEarthWoodworks" on YouTube and his articles appear monthly in Highland Woodworking's on line newsletter "Wood News Online.".

Hope these top Woodworking YouTube Channels help you with all your future DIY woodworking projects! Make sure to use General's woodworking tools, like our best-selling Heavy Duty, All-In-One Aluminum Pocket Hole Jig Kit, 76 Piece Set With Carrying Case, or the 822 Digital Angle Finder Rule, 5-Inch. Use both tools and create a frame as your next DIY project!
Woodworking tools at Highland Woodworking - shop our comprehensive tool selection for the best in woodworking tools. Our lines include woodworking hand tools & power tools, joinery jigs, The World's Safest Tablesaw and The Best Bandsaw Blade Selection. Along with woodworking tools from top tool brands, we stock the woodworking materials & supplies you need everyday. View all tools at Highland Woodworking home to over 10,000 Woodworking Tools or browse through our Woodworking Tools sub-categories below. Be sure to check out our Woodworking Tool Sale page where you will find special offers and tool deals.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
I wanted to have numerous outlets, and have enough elec­trical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.
My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
Another staple in the beginner woodworkers tool kit has to be the cordless drill. Used for either drilling holes or driving fasteners, this tool gets used on almost every project. There a tons of options here regarding size of batteries, aka power, but something around the 18-20 volt range is a good all-around size that will not leave you constantly wishing you had something larger or smaller. Here is a large accessory kit at a good price that should give you most of the drivers a bits you will need.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Teak is an excellent choice, the “crème de la crème”, for fine outdoor furniture. Teak is highly weather-resistant by nature, which means that it does not have to be weatherproofed when used outdoors – although it often is finished and stained for aesthetic purposes. Teak is one of the most expensive exotic hardwoods there are, but it will look absolutely beautiful and maintain its integrity over time.
My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.

Since I long ago lost the woodcarving tools I used to own as a youth, I figured I would focus on something larger. With my current ideas of doing a commercial greenhouse venture, I have considered making my first project one of a pergola for training plants up as a living shade-tent area. I have also considered trying to do an earth-sheltered greenhouse assuming I can figure out a loophole in city ordinances and/or coax the officials to sign off on it. I would love to do some hand-carved bowls and eventually make my own workbench and maybe even craft other things like a shaving horse. A foot-powered lathe is another one that I still find fascinating from the Foxfire books.


"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
I ONLY use water as a lubricant on all my stones. When they get clogged I take a nail brush and hand dish detergent to them to clean them. When a carborundum stone gets worn I do figure 8s on a flat piece of concrete with lots of water to reflatten it. I don’t like oil because it gums up over time and is then harder to clean. I keep a carborundum and a Quachita stone by the kitchen sink for knives. I probably haven’t used the carborundum stone in several years. I scrub the Quachita stone at roughly 18-24 month intervals. It’s white, so it’s easy to see the steel accumulating. I can feel a noticeable difference after scrubbing the stone. This has been my standard practice for almost 50 years, so I’m not inclined to change it.

Pine is of the most common softwoods and comes in several varieties, including White, Knotty and Yellow – all of which can be used to make furniture. Pine is fairly easy to work with, as it is very soft, but it will show wear and tear more easily with everyday use (which could be a good or bad thing, depending on the look you prefer). Pine can either be stained or painted and often gives a more traditional feel to a piece – especially when using repurposed Pine flooring and siding. Pine is a practical and affordable choice for shelving, tables, closets, and cabinetry.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.

Although we focus primarily on the use of wood in our work, CZ Woodworking also incorporates materials other than solid wood into our workshop. We work with metalworkers, glass companies, designers and artisans alike to bring various materials together to create custom pieces. Examples of additional materials we use are wrought iron, steel, glass, stone and more. By combining various mediums together, we are able to achieve the specific look that fits your needs best. Please contact us directly to inquire further.

Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
×