About Youtuber Have you ever considered woodworking as a hobby but didn't where to begin? Tune in for this video series from the editors of Fine Woodworking magazine, and we'll guide you through the process. From choosing your first tools to setting up a workspace to completing your first woodworking projects, you'll discover just how easy it is to get started in woodworking.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.

I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!

Although we focus primarily on the use of wood in our work, CZ Woodworking also incorporates materials other than solid wood into our workshop. We work with metalworkers, glass companies, designers and artisans alike to bring various materials together to create custom pieces. Examples of additional materials we use are wrought iron, steel, glass, stone and more. By combining various mediums together, we are able to achieve the specific look that fits your needs best. Please contact us directly to inquire further.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
Ash is a white to pale brown wood with a straight grain. It’s pretty easy to work with, is a fairly hard and dense wood, and takes to stain quite nicely. Ash has a medium to coarse texture similar to oak. The grain is almost always straight and regular, though sometimes moderately curly or figured boards can be found. Ash is becoming harder and harder to find, so it ranks as an increasingly expensive material to use.

Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.

For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
Do you enjoy woodworking?  Do you have a budget that you have set aside just for your woodworking?  If you are not a millionaire, than more than likely you will have some sort of a budget.  Let me give you a little insight into why you are here and what you will find on this site.  Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job?  Or maybe you are wanting to turn your hobby into a full time job.  If that sounds like you than  your in the right place.

The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
×