I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flat­tening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelo­gram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.


A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Not only is having a full time job is hard to do woodworking, if you have a family as well, then that is another thing that you are going to have to juggle as well.  For me its a no brainer.  I always choose my family over my hobby of woodworking.  But when my family or job does not need my presence, that’s when I am free to let my brain just run loose on new ideas of what to build next.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
One of the most essential aspects of designing any custom piece is determining what type of raw material to use. This element will help to define the piece by assuring that you will get the look and feel that you want for your home or business. Whether it is traditional, rustic, farmhouse chic, industrial or a contemporary design, the material selected will help obtain that sense of style. More so, creativity and collaboration between the customer and CZ Woodworking will allow that raw material to come to life!

Just how small?  Will you have an extra bedroom for your shop or will you be doing woodworking in your living room?  Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time?  A while back FWW had a video tour of a shop in Japan that was smaller than small.  I'll try to find it and get back.  Found it...  shows what can be done in a small space but this shop was not on a small budget so no help there. 

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post. 

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
One of the great furniture woods, Mahogany has a reddish-brown to deep-red tint, a straight grain, medium texture and is moderately hard. It takes stain very well, but looks great with even just a few coats of oil on it. For an even more distinguished look, exotic African Ribbon-Striped Mahogany adds amazing grain and texture elements to this already beautiful species of wood.
These are without a doubt the most adorable things ever. The fact that you make them with coffee filters and they are cheap does not cloud my judgment, either. They are really easy to make though and so creative. These coffee filter pom poms would look so adorable hanging in a little girl’s bedroom or just anywhere that you want a bit of decoration. You can use them to decorate the deck for summer parties or make really large Christmas ornaments from them. Either way, you just need disposable coffee filters, some hot glue, sturdy cardboard and string and you can find the tutorial over at Bored & Crafty.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.

So I am curious about what the best choices in woodworking tools would be for someone who is just beginning to develop the skills involved with the craft. Funds would be limited and at least for me, I have a strong preference for non-electric tools when possible. Not only what would be the best tools to start a collection with, but also what would be a good way to obtain them aside from ebay, pawn shops and antique shops?
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
How about a hunk of butcher block counter top on a 4X4 (legs) base on locking wheels.  Round over the good side and it is a rolling kitchen stand - chopping block -  island.  Flip the top over, lock the wheels, and it's a bench.  There is a vise that is sold by Woodcraft that drops onto a mounted post in both vert and horiz positions that would be perfect for a small flip top bench.  The post would be mounted to the underside, unseen till the top was flipped and the vise dropped on.  It pivots but when the jaws are clamped it is tight.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.

I taught (teach) several aspects of "green woodworking" and related subjects, so I love your question. The buying and using of old tools is great...no matter the source. However, I have seen much frustration ensue over getting them adjusted, and "work ready." As often a beginner with limited budgets, also have limited traditional skill sets as well in understanding these tools and sharpening them. You must be patient with yourself, as tuning these old tools up will be very time consuming. Sharpening (and the proper tools of sharpening) should be your first acquisition. So many folks buy chickens before building a proper "chicken coop." Traditional tools are the same way, as there is no reason to own them, if you can't keep them properly honed.
Often referred to as Douglas Fir, this softwood has a rather straight, pronounced grain that has a reddish brown tint to it and is moderately strong and hard for a softwood. Fir is most often used for construction building materials, however it’s inexpensive and can be used for certain aspects of furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain uniformly, so it’s best when used in projects that require a painted finish.
For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.

Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.

Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.


The second big tool you need is a saw. There are many types of saws, and this can be the trickiest part of setting up a shop on a budget. As a beginner, you'll likely be using woodworking books, magazines and websites for instruction and inspiration. Unfortunately, most of these sources consider a table saw a beginner tool. For those of us on a budget, or with little space, a table saw may not be an option. They cost several hundred dollars to start, and take up several square feet of floor space. Instead, look for a good circular saw that allows you to adjust the depth and angle of cut. It's also nice to have a laser to help guide the cuts. You can get a decent circular saw for around $100.
Poplar is one of the less expensive hardwoods. It’s also fairly soft, considering it is a hardwood, which makes it easy to work with. Poplar is very light in color (almost “white”) with some green or brown streaks in the heartwood (the wood that comes from the center of the tree). Because poplar is not the most beautifully grained wood, it’s almost always painted as it does take to paint very nicely for a uniform finish. Poplar makes for great table bases (often painted, with a stained tabletop of a different wood), drawers, cabinets, hutches and more. Poplar is a very common wood that is versatile and cost efficient.

These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
As the mother of 4 children, 3 of whom are busy boys, much of Jen's free time is spent at the ball field, brushing up on video game terminology and building Lego towers. Jen is the owner and creative mind behind Banner Events. With a passion for event planning & party styling and an obsession with the little details that take an event from ordinary to extraordinary, Jen wakes up every morning excited to get to work.
Use the square and position the pivot point onto the board top and slide the square up to the 5 on the line up “COMMON TOP CUT” outside the board. Mark the line as for the angle. After first angle is cut, measure the rafter length from the tip cut to get the seat cut measurement. Mark the seat cut and place the pivot point onto this mark and do the same step to get 5/12 angle. From that angle, measure up 2 ½” and make the line.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
One of the great furniture woods, Mahogany has a reddish-brown to deep-red tint, a straight grain, medium texture and is moderately hard. It takes stain very well, but looks great with even just a few coats of oil on it. For an even more distinguished look, exotic African Ribbon-Striped Mahogany adds amazing grain and texture elements to this already beautiful species of wood.
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
As an x aerospace machinist I have run manual lathes and mills and programmed and run CNC as well. IMO a manual lathe is far more versatile and useful than a CNC for the average DIY buff. A CaN C is basically a very accurate production machine but to spend time programming, setting up, proving out just for a couple or several pieces is not practical ( unless you have money and time to spare)

Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
The variety of colors and tones, textures, and grain patterns seen in most hardwoods create some of the most beautiful and unique furniture in the world. Hardwoods are generally more expensive than softwoods, but the finished look can be well worth the additional cost. Hardwoods are often more durable and are therefore generally recommended for tabletops and countertops. Many hardwoods do not need to be stained, but rather hand-finished with natural oils to enhance their beautiful grain and texture.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
What better way to continue our #2x4andMore week on the 4th of July than with 4x4s! 4×4 wood posts are good for more than just fences and beams. We’ve rounded up 15 of our favorite 4×4 wood crafts to inspire your DIY creativity. You can buy brand new 4×4 posts at your local hardware store or find 4×4 scrap wood. Either way you’ll only need to a few more materials to make your 4×4 wood crafts into a reality.

Being able to create and build a masterpiece from pieces of wood is more than a hobby -it’s a craft. Buying all the tools and supplies you need can start to add up to some serious money. But there are ways to enjoy building with wood without breaking your budget. Here’s a few woodworking tips that may get you started saving money and still being creative.

About Youtuber This channel features work done by Marsh Wildman of Wildman Technology & Fabrication. I'm a maker/artisan/technologist specializing in bringing the dreams of others to reality. If you can convey your concept to me, I can build it for you! We reclaim and upcycle when possible. Wood working projects. Plasma cutting and welding. Machine shop services, PROTOTYPING and setting up production lines. 

Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Available in both water-based and oil-based finished, polyurethane is one of the most common practices used in woodworking today. Polyurethane can be sprayed, brushed or rubbed onto the piece to obtain either a satin, semi-gloss or glossy finishes. Polyurethane is a very versatile finish that will last for many years and is easy to clean and maintain.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
The third tool for the beginner is the Jigsaw. A jigsaw allows the user to cut curved and circular patterns in stock. Sure, a band saw will likely be more accurate and can cut thicker stock, but for the beginner, the jigsaw (sometimes also referred to as a Sabre Saw) can be perfectly effective. For versatility, choose an orbital-action, corded jigsaw that feels good in your hand and has an easy blade changing system.

In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.


As far as advice goes, I'm like a lot of the other folks on this thread; make a shop budget that fits into your existing budget and stick to it. Whenever you can foresee a larger expense, skrimp and save, cut costs in other areas of non-essential spending, and accept that sometimes, you NEED to go outside of your budget. In my experience, if it means enough to you, you can make it work. Good luck!


I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Birch is readily available and less expensive than many other hardwoods. Birch is stable and easy to work with. However, it’s hard to stain because it can get blotchy, so it is generally preferred to paint Birch.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
As far as advice goes, I'm like a lot of the other folks on this thread; make a shop budget that fits into your existing budget and stick to it. Whenever you can foresee a larger expense, skrimp and save, cut costs in other areas of non-essential spending, and accept that sometimes, you NEED to go outside of your budget. In my experience, if it means enough to you, you can make it work. Good luck!
In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.
There are some basic things every woodworker needs to get started. Assuming you aren't the kind of person that does everything with hand tools, you'll first need a drill. Power drills come in many different styles and price ranges. The popular trend right now is for companies to make cordless tool systems that all run off of the same battery packs, and a drill is often the first tool a person gets in the set. Cordless drills are popular and handy for doing household tasks , such as hanging picture frames; but for serious woodworking, they can lack power and might die in the middle of a job. Corded drills are a less expensive option and often work better for the tasks you'll be doing in a wood shop; just get a cheap extension cord to go with it. You can easily find a corded drill of good quality for about $100.
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.

Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.

×