If you had bothered to watch the video this would have been explained. The cupping you see is a result of mass manufacture. Few tool makers will take the time to lap the back of a chisel to degree a craftsman will (much less the bargain brand he’s using). It’s simply not practical for them to do so and still make their price point. Some higher end (Lee Nielsen, Lee Vally, Veritas) chisels will be closer but even these will require some degree of hand honing/lapping. Using a flat stone, with at most couple hours of practice, you will reliably create razor sharp straight edges.
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
Do you enjoy woodworking? Do you have a budget that you have set aside just for your woodworking? If you are not a millionaire, than more than likely you will have some sort of a budget. Let me give you a little insight into why you are here and what you will find on this site. Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job? Or maybe you are wanting to turn your hobby into a full time job. If that sounds like you than your in the right place.
There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
One of the great furniture woods, Mahogany has a reddish-brown to deep-red tint, a straight grain, medium texture and is moderately hard. It takes stain very well, but looks great with even just a few coats of oil on it. For an even more distinguished look, exotic African Ribbon-Striped Mahogany adds amazing grain and texture elements to this already beautiful species of wood.
She came back to the mainland when her family was building a sky scraper in Denver. ( Well about as tall as any of the other down town high rises.) I got to tour it while it was being built. Very cool ! So hanging around this crew of a family she picked up quite a lot. The wife of her brother, the iron worker and pro chef, was an iron worker as well. The first lady ironworker I had ever met and I grew up around construction workers some what. Hard core people ( bound to rub off ).
Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Thanks for the acknowledgement. My goal is for viewers like yourself to be able to focus 100% on the video’s content, woodworking. Most woodworking apprentices will ask the journeyman to show them how it is done. At the same time, many beginning woodworkers do not know what questions to ask. By showing you on the video, you are able to think for yourself and to also formulate important questions to ask. With that said, the more you watch each video, the more you will learn about woodworking skills and techniques. (some things in the videos are subtle that you may not pick up on the first viewing.)
Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
My name is Marc Spagnuolo and welcome to my channel. I am a podcaster, video producer, author, and woodworking enthusiast. I have contributed articles and video content to FineWoodworking.com, Popular Woodworking Magazine and WOOD Magazine. Producing the Wood Whisperer is a great way for me to combine four of my passions: woodworking, technology, education, and humor. I believe that even the most complicated woodworking project is just a series of steps. My goal with this channel is to show you the tools and techniques you need to perform those steps.