Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.

Thanks for the acknowledgement. My goal is for viewers like yourself to be able to focus 100% on the video’s content, woodworking. Most woodworking apprentices will ask the journeyman to show them how it is done. At the same time, many beginning woodworkers do not know what questions to ask. By showing you on the video, you are able to think for yourself and to also formulate important questions to ask. With that said, the more you watch each video, the more you will learn about woodworking skills and techniques. (some things in the videos are subtle that you may not pick up on the first viewing.)
Often referred to as Douglas Fir, this softwood has a rather straight, pronounced grain that has a reddish brown tint to it and is moderately strong and hard for a softwood. Fir is most often used for construction building materials, however it’s inexpensive and can be used for certain aspects of furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain uniformly, so it’s best when used in projects that require a painted finish.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.

One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.


Poplar is one of the less expensive hardwoods. It’s also fairly soft, considering it is a hardwood, which makes it easy to work with. Poplar is very light in color (almost “white”) with some green or brown streaks in the heartwood (the wood that comes from the center of the tree). Because poplar is not the most beautifully grained wood, it’s almost always painted as it does take to paint very nicely for a uniform finish. Poplar makes for great table bases (often painted, with a stained tabletop of a different wood), drawers, cabinets, hutches and more. Poplar is a very common wood that is versatile and cost efficient.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.

Even the backside grinding shown in the single frame of the video shows the effects of hand held sharpening. There is a curve on the flat side of the blade! Starting to look like a spoon. It’s impossible to get a flat surface when using bones and tendons. This effect was exploited to make the first lens when done in glass. Telescope mirror grinders do it too using two different hardness of glass, if machine done it would be flat. If those “slate” tiles are flat they must be ground flat not baked. No need to check.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
About Youtuber Here you will find everything from money saving tips, woodworking projects, jigs and completely wild contraptions. I have been building and designing since I was old enough to swing a hammer. With a mind for out of the box thinking and an unusual mix of artfull design and engineering interest, you never know whats going to happen next.
About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.  

The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
All in all, for whatever reason it is that you enjoy woodworking, then you always need to follow that passion.  There is always going to be obstacles to overcome, whether that be not enough money to buy your tools, or space to put those tools, or time to enjoy woodworking.  That is something that every person has to overcome.  Everybody has there own unique obstacles.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools.  It is sort of an inexpensive crash course in hand tools.  Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read.  Use the internet to learn all you can about a tool before buying.  The tools you need are dictated by what you want to build.
×