The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Since I long ago lost the woodcarving tools I used to own as a youth, I figured I would focus on something larger. With my current ideas of doing a commercial greenhouse venture, I have considered making my first project one of a pergola for training plants up as a living shade-tent area. I have also considered trying to do an earth-sheltered greenhouse assuming I can figure out a loophole in city ordinances and/or coax the officials to sign off on it. I would love to do some hand-carved bowls and eventually make my own workbench and maybe even craft other things like a shaving horse. A foot-powered lathe is another one that I still find fascinating from the Foxfire books.
About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living in a great craft. My hat is off to all of you.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
Check with Habitat for Humanity. If they have a store you may find several good items such as a bench, bandsaw or etc. When I retired and moved I donated a complete shop full of woodworking power tools and hand tools to Habitat. They sold them, I deducted them from my income tax. Unfortunately I could not retire my desire to woodwork and at age 78 I built a shop and use only hand tools and a bandsaw. Good exercise pushing a LN #7. Build yourself a solid bench with some southern pine with a moxon vise that can be built by hand. Get some holddowns!
If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.
We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.