Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.
Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
Often referred to as Douglas Fir, this softwood has a rather straight, pronounced grain that has a reddish brown tint to it and is moderately strong and hard for a softwood. Fir is most often used for construction building materials, however it’s inexpensive and can be used for certain aspects of furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain uniformly, so it’s best when used in projects that require a painted finish.
Kids love DIY projects, especially when they get to give those projects away as gifts. You can help your little ones to make a great picture frame for Father’s Day with just a few twigs and a hot glue gun. Just glue the twigs to the frame and let the kids decorate however they want. Use burlap for the matting and add a special message with a Sharpie.
Danish Oil is an oil-based finish that soaks deep into wood pores to provide protection from the inside out. Generally made from a unique blend of penetrating oil and varnish that stains, seals and protects all at the same time, it enhances the natural look and feel of the wood, and creates the rich, warm glow. This finish is ideal for furniture, trim, molding or any other bare wood interior surface that calls for an accentuated look.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motionâ€”an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.
Available in both water-based and oil-based finished, polyurethane is one of the most common practices used in woodworking today. Polyurethane can be sprayed, brushed or rubbed onto the piece to obtain either a satin, semi-gloss or glossy finishes. Polyurethane is a very versatile finish that will last for many years and is easy to clean and maintain.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws. Because of this, I'd stick to the two saws we looked at in the $500 build: The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110. These two additions bring our running total to just over $500.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!