Even the backside grinding shown in the single frame of the video shows the effects of hand held sharpening. There is a curve on the flat side of the blade! Starting to look like a spoon. It’s impossible to get a flat surface when using bones and tendons. This effect was exploited to make the first lens when done in glass. Telescope mirror grinders do it too using two different hardness of glass, if machine done it would be flat. If those “slate” tiles are flat they must be ground flat not baked. No need to check.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
The trick is to use sandpaper. It’s a good quality abrasive material and is readily available. You’ll want a selection of different grits – low grits to get started, higher grits when finishing. The reason this is cheaper is that you can get a selection of 5-10 different sandpapers for under $20. Getting even a couple of decent sharpening stones wouldn’t be possible at that price. In the long run, they’ll last longer but this is a budget option we’re talking about.
In fact when I first met her she had walked away from a construction job building three story apartment housing.  One day they were working on the third floor with a fairly high wind , and speaking of plywood, there were stacks of plywood up there and she tried to tell the guys they needed to secure the plywood or they would start to take off like playing cards.

If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
About Youtuber LAB11 Created designer furniture from scratch from wood and recycled materials like pallets or customizes and repairs existing furniture. The watchwords for our creations and customizations are: Pretty, durable and solid things. Here are the videos of some projects creations but also of layout of the workshop, A video per month out at least.
The second big tool you need is a saw. There are many types of saws, and this can be the trickiest part of setting up a shop on a budget. As a beginner, you'll likely be using woodworking books, magazines and websites for instruction and inspiration. Unfortunately, most of these sources consider a table saw a beginner tool. For those of us on a budget, or with little space, a table saw may not be an option. They cost several hundred dollars to start, and take up several square feet of floor space. Instead, look for a good circular saw that allows you to adjust the depth and angle of cut. It's also nice to have a laser to help guide the cuts. You can get a decent circular saw for around $100.

These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.


Ron Paulk is an extremely likeable mystery and I think he deserves 10x more subscribers than he has. I'm convinced he's a secret millionaire - he has a workshop in what seems to be the 20-car garage of a multi-million dollar mansion - which he claims belongs to a friend and he's only using it temporarily while they sell the house.  I think it's been five years now that he's been there.  But anyway, Ron is mainly a finish carpentry contractor - that's things like baseboard, fireplaces, kitchen cabinets etc.  He is a master craftsman.  What makes him unique is his approach to working - he is all about being portable, mobile and lightweight.  Every year he seems to fit out a new van or trailer as a mobile woodshop.  I've built Ultimate Workbench, Chop Saw station and fitted out a van following his designs.  He introduced me to Festool, which was a costly mistake for me!  I've built a lot of his projects, and I learned a whole lot along the way.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
Woodworker’s Hardware is your one-stop online woodworker’s store for all of your woodworker's supplies.  Shop for everything you need to start and finish your woodworking projects.  Find a huge selection of hardware products including drawer slides, barn door hardware, lazy susans, kitchen cabinet hardware & accessories, and furniture hardware.  We stock thousands of door and cabinet hardware and accessories like knobs, pulls, and hooks for kitchens, bathrooms, and closets. As one of the leading online kitchen cabinet hardware suppliers, shop for soft-close ball bearing drawer slides from top-rated brands like KV and Blum. Check out our sales page for our best offers! Our fully stocked warehouse full of woodworker’s supplies ensures shipping in 24 business hours.

My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
By the way, before you yell at me about the fact that the price on the links for the nail gun is more than $200, listen up I have a handy tip:  There are sales throughout the year on this exact package for $200.  That’s how I bought mine.  Just keep checking back.  And be sure to follow me on social media.  I keep checking it, too and if I see it’s on sale, I will post it to let you all know!
In addition to the type of finish you want, the location of the final installation should be considered when choosing a hardwood species. While it won't have as much bearing on furniture pieces to be used indoors, you may want to consider some more moisture-resistant species (such as cypress or the ever-increasingly endangered teak) for outdoor projects. Again, your local woodworking supplier will be able to help with this decision if you are unsure about what species might work well for your particular application and climate.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
On the money issue one`thing I did is find something that is fairly easy to make and easy to sell. I made kaleidoscopes to begin with and still whip up a batch if I need to buy wood or a new tool. A neighbor WW makes wooden condiment holders for restaurants. A good friends son worked his way thru college by making a certain bearing that they needed on his tiny lathe. Spend a month or so on $$$ stuff before doing the better stuff.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
There are some basic things every woodworker needs to get started. Assuming you aren't the kind of person that does everything with hand tools, you'll first need a drill. Power drills come in many different styles and price ranges. The popular trend right now is for companies to make cordless tool systems that all run off of the same battery packs, and a drill is often the first tool a person gets in the set. Cordless drills are popular and handy for doing household tasks , such as hanging picture frames; but for serious woodworking, they can lack power and might die in the middle of a job. Corded drills are a less expensive option and often work better for the tasks you'll be doing in a wood shop; just get a cheap extension cord to go with it. You can easily find a corded drill of good quality for about $100.

This is known as the “Scary Sharp” method and I first learned of it on Usenet back in the day. I’ve had pretty good luck only going up to 2000 grit automotive paper. That stuff is commonly available near the spraypaint at Wally-world. At this grit, I can easily shave the hair on my forearm. For a plate, I use a single 12×12 tile from a Big Box store.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Some DIY woodworking projects are too intimidating to even attempt because you don't think of yourself as a master woodworker. Backyard Woodworking dubs itself as the YouTube channel for the average guy. The channel takes you through simple projects you can do today, projects like a piggy bank, a birdhouse and a heart box—which is apparently the perfect gift for your sweetie!
Carpenters Builders Pencils 13pc Joiners Sharpener Soft-lead oval-section carpenters pencils for marking timber, brick, stone and other building materials. Draws thick or thin lines on both rough and smooth surfaces. Oval-shaped length means pencils do not roll away when placed on inclined surfaces. Includes 12 pencils and a sharpener. Pencils supplied are in BLUE.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
So I am curious about what the best choices in woodworking tools would be for someone who is just beginning to develop the skills involved with the craft. Funds would be limited and at least for me, I have a strong preference for non-electric tools when possible. Not only what would be the best tools to start a collection with, but also what would be a good way to obtain them aside from ebay, pawn shops and antique shops?
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
Kids love DIY projects, especially when they get to give those projects away as gifts. You can help your little ones to make a great picture frame for Father’s Day with just a few twigs and a hot glue gun. Just glue the twigs to the frame and let the kids decorate however they want. Use burlap for the matting and add a special message with a Sharpie.

Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house.  If you don’t have one, they are a few bucks each and WELL worth the investment.  AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂


Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
About Youtuber This channel features work done by Marsh Wildman of Wildman Technology & Fabrication. I'm a maker/artisan/technologist specializing in bringing the dreams of others to reality. If you can convey your concept to me, I can build it for you! We reclaim and upcycle when possible. Wood working projects. Plasma cutting and welding. Machine shop services, PROTOTYPING and setting up production lines.  

What better way to continue our #2x4andMore week on the 4th of July than with 4x4s! 4×4 wood posts are good for more than just fences and beams. We’ve rounded up 15 of our favorite 4×4 wood crafts to inspire your DIY creativity. You can buy brand new 4×4 posts at your local hardware store or find 4×4 scrap wood. Either way you’ll only need to a few more materials to make your 4×4 wood crafts into a reality.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
I’ve been seeing a lot of maker sites featuring both Osmo Polyx and Rubio Monocoat finishes (hardwax oils).  They seem to go nicely with the live edge tables that are so popular today.  I imagine these companies are doing a good job reaching out to the makers because it seems like an effective effort.  I’ve also seen some examples of Odie’s Oil and and it looks like a similar product only with less marketing flair.  I was on the fence and was leaning toward Rubio, only because it seemed like more makers were featuring it.   Then I ran across this series of 4 videos by Blacktail Studio that test out hardwax finishes each of 4 different ways.
For under $20 I am very impressed with the Bad Blade Carver by Kwik Tool.  Mounted in a 4.5″ grinder, it removes a ton of material quickly yet allows a fair amount of control.  The disk has only 6 teeth so the carver is mainly a solid disk with very few teeth to bite and create kick-back or dig-in. I found I had the best control when engaging the blade between 12 o’clock (top of the grinder) and 3 o’clock. When in that range it was not overly aggressive and left me in control.

About Youtuber Here you will find a wide range of woodworking and do-it-yourself topics, including: wood gear mechanisms, wood gear clocks, cyclone separators, dust collectors, modification of tools for dust collection, tips & tricks, home building and repair, electrical & electronic, building the John Smith Senior 20 Organ, antique vehicles and more.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
The Jay's Customs Creations YouTube channel releases weekly videos on shop projects and dimensional lumber projects. Jay's show can really help you if you want to do DIY woodworking projects on a budget. He sometimes shows viewers how to complete the project without electricity and using only hand tools. He goes over the prices he paid for materials to give people a realistic budget for the project before they get started.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!   
×