This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Another option is to use two small clamps to hold two boards in place, and then wedge the wood pieces, that you’re trying to glue, in between them. I’ve found that this works better than the ratchet straps when trying to glue up thinner lumber, like boards from old pallets. When using this method, you should have the wood on a completely flat surface, and often it helps to put some weight on top to keep it from bowing.
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday. 

Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
When I bought my miter saw, I didn’t buy the cheapest, but I didn’t want to spend a ton of money. I started out with a small Hitachi.  I LOVE my saw and it does a great job—I have no complaints.  However, I do kind of wish I had gotten a larger one.  Here’s the thing.  I can cut up to a 1×6 board in one pass on my miter saw.  But if I cut any larger than that, I have to flip the board over and cut again from the other side.  That means if I’m making something from 1x8s or wider, I have to make twice as many cuts.  Sometimes this is a pain.  But it’s obviously not a big enough pain for me to spend the extra money to go buy a bigger one haha.  Just something to consider. Either way, a miter saw of any size is guaranteed to be a good investment.  Also, watch out for sales on this saw…it’s often listed on sale for $100 (that’s how I got mine!).
John Heisz is a Canadian woodworker who makes many of his own tools to help him with his projects. His YouTube channel shows you how to also make your own tools. He has a video series on how to make homemade clamps, whether you're making hand screw clamps, wooden bar clamps or a deep c clamp. Another one of his video series takes you through the making of your own homemade vise.

I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate.  So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it.  I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.


For many tasks you may not gain much benefit from going above 4-500 grit but polishing your axe to 0.33 micron certainly won’t affect edge retention. For finishing work, you certainly do want as well polished of an edge as possible since that means less scraping or sanding. A well honed plane can leave a surface that’s actually too smooth for painting.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.

This is sequential to step one, but with a little difference. You choose simple and easy woodcrafts to make.  Ones that do not require investment in expensive tools. Nor do they require a lot of wood and raw materials. There are plenty of examples of such projects to be found. We have written about a few of them here. Small and popular wood projects can be made in large numbers and sold with ease, for a high profit. 


Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.

As an x aerospace machinist I have run manual lathes and mills and programmed and run CNC as well. IMO a manual lathe is far more versatile and useful than a CNC for the average DIY buff. A CaN C is basically a very accurate production machine but to spend time programming, setting up, proving out just for a couple or several pieces is not practical ( unless you have money and time to spare)

Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
×