If you'd like to learn more about the differences between hardwood species, I can think of no better resource than R. Bruce Hoadley's 1980 masterpiece, Understanding Wood: A Craftsman's Guide to Wood Technology. Not only does Hoadley detail nearly every species used for woodworking, he does an exceptional job at describing how to prepare, work with and finish these hardwoods. This is an industry-standard resource, one that I'd highly recommend to every woodworker.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
John Heisz is a Canadian woodworker who makes many of his own tools to help him with his projects. His YouTube channel shows you how to also make your own tools. He has a video series on how to make homemade clamps, whether you're making hand screw clamps, wooden bar clamps or a deep c clamp. Another one of his video series takes you through the making of your own homemade vise.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
About Youtuber Have you ever considered woodworking as a hobby but didn't where to begin? Tune in for this video series from the editors of Fine Woodworking magazine, and we'll guide you through the process. From choosing your first tools to setting up a workspace to completing your first woodworking projects, you'll discover just how easy it is to get started in woodworking.
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
I Like to Make Stuff is the perfect channel for beginners who want comprehensive teaching on woodworking. It has a show called Maker 101 that goes into the basic skills you need to start making stuff. I Like to Make Stuff is not intimidating to the beginner because it isnâ€™t afraid of showing woodworkers making mistakes on their project rather than always doing everything perfectly.
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!
In fact when I first met her she had walked away from a construction job building three story apartment housing. One day they were working on the third floor with a fairly high wind , and speaking of plywood, there were stacks of plywood up there and she tried to tell the guys they needed to secure the plywood or they would start to take off like playing cards.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
One tool that I’ve used over and over when my clamps were too small, is ratchet straps. They come in handy when trying to glue several pieces together, like when making a table top out of 4 x 4’s. One problem though, is that when using ratchet straps on smaller pieces of wood, or longer boards, it’s possible to warp the piece you’re trying to make. However, if you’re careful, a ratchet strap can stand in for a clamp or two.
One of the most heavily used tools in your shop will be your table saw. It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs. Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40. A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits. As you work on a few projects you may find that more specialized bits are needed. But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.
About Youtuber This channel is created to share my passion for woodworking and guide beginners into realizing the joy of this hobby. Woodworking is fun, inspiring and helps you to design, create and relax. You can pick up a piece of wood and create something out of it and the result is uplifting. You just created something valuable from piece of wood.
About Youtuber LAB11 Created designer furniture from scratch from wood and recycled materials like pallets or customizes and repairs existing furniture. The watchwords for our creations and customizations are: Pretty, durable and solid things. Here are the videos of some projects creations but also of layout of the workshop, A video per month out at least.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge. Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
I use a 9″ x 12″ Chinese grade B surface plate and wet the back of the carborundum “sandpaper” to hold it in place. Obviously not the “budget” version, but I have the surface plate for other purposes. At about $17 from ENCO it wasn’t very expensive. And it *really* is flat to better than 0.001″. So the thickness of the paper is the biggest error. I also have a good assortment of Arkansas and other types of stones, though none of the Japanese waterstones. I generally don’t use the surface plate unless the edge is really bad e.g. an abused tool picked up at a yard sale.
All in all, for whatever reason it is that you enjoy woodworking, then you always need to follow that passion. There is always going to be obstacles to overcome, whether that be not enough money to buy your tools, or space to put those tools, or time to enjoy woodworking. That is something that every person has to overcome. Everybody has there own unique obstacles.
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools. It is sort of an inexpensive crash course in hand tools. Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read. Use the internet to learn all you can about a tool before buying. The tools you need are dictated by what you want to build.