Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
Right now you're thinking, "but the plans say to use a table saw for this." That's OK , because the great thing about a circular saw is you can turn it into a table saw. There are plenty of videos online showing how to do this, but you are essentially cutting a slot in a piece of plywood, mounting the circular saw to it, and flipping it over. With careful planning you can have a good basic table saw without spending hundreds of dollars, and it can come apart if you need to save space. With that setup you can cut long pieces of wood that you may not be able to brace properly to cut with the circular saw. You can also make more accurate cuts than by holding the circular saw. It can also be used to cut simple dados and to cut a bevel. You do need to be careful, as it won't have the blade guard covering the saw blade anymore.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
About Youtuber This channel features work done by Marsh Wildman of Wildman Technology & Fabrication. I'm a maker/artisan/technologist specializing in bringing the dreams of others to reality. If you can convey your concept to me, I can build it for you! We reclaim and upcycle when possible. Wood working projects. Plasma cutting and welding. Machine shop services, PROTOTYPING and setting up production lines.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
I wanted to have numerous outlets, and have enough electrical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living in a great craft. My hat is off to all of you.
When I bought my miter saw, I didn’t buy the cheapest, but I didn’t want to spend a ton of money. I started out with a small Hitachi. I LOVE my saw and it does a great job—I have no complaints. However, I do kind of wish I had gotten a larger one. Here’s the thing. I can cut up to a 1×6 board in one pass on my miter saw. But if I cut any larger than that, I have to flip the board over and cut again from the other side. That means if I’m making something from 1x8s or wider, I have to make twice as many cuts. Sometimes this is a pain. But it’s obviously not a big enough pain for me to spend the extra money to go buy a bigger one haha. Just something to consider. Either way, a miter saw of any size is guaranteed to be a good investment. Also, watch out for sales on this saw…it’s often listed on sale for $100 (that’s how I got mine!).
Eastern Hemlock, the state tree of Pennsylvania, is a softwood that has a naturally light-reddish-brown color. Although Western Hemlock (sourced from the Pacific Northwest) is often used in furniture building due to its straight grain and finer texture, which sands to a silky, reflective smooth surface. Hemlock gives some hardwoods a run for their money in terms of durability and strength, but at a more approachable price point. Reclaimed Hemlock has made its way into local salvage yards in recent years, and is being utilized in all aspects of woodworking and furniture building.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.