Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless. 

Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.

Do you enjoy woodworking?  Do you have a budget that you have set aside just for your woodworking?  If you are not a millionaire, than more than likely you will have some sort of a budget.  Let me give you a little insight into why you are here and what you will find on this site.  Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job?  Or maybe you are wanting to turn your hobby into a full time job.  If that sounds like you than  your in the right place.
This is sequential to step one, but with a little difference. You choose simple and easy woodcrafts to make.  Ones that do not require investment in expensive tools. Nor do they require a lot of wood and raw materials. There are plenty of examples of such projects to be found. We have written about a few of them here. Small and popular wood projects can be made in large numbers and sold with ease, for a high profit. 

Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.

For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap.  ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15).  1 rip handsaw (used ones can be found at Antique stores for $20 or less.  Try to find one that is fairly sharp to start with).  Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both).  A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
This is sequential to step one, but with a little difference. You choose simple and easy woodcrafts to make.  Ones that do not require investment in expensive tools. Nor do they require a lot of wood and raw materials. There are plenty of examples of such projects to be found. We have written about a few of them here. Small and popular wood projects can be made in large numbers and sold with ease, for a high profit. 
If you’ve been reading my regular blog, unbrokenfurniture.com, then you already know that I’m a novice furniture upcycler. Up until now I’ve been repairing and refinishing existing furniture. Lately I’ve been picking up more and more reclaimed wood and other raw materials, so I’ve decided to learn to build some furniture from scratch. Because building furniture from scratch doesn’t really fit with the theme of unbrokenfurniture.com, I’ve decided to keep these projects on a separate space, hence woodworkingwednesdays.com was born. I’m planning to post one new project each week (hopefully Wednesday).
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.

Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged. 

Often referred to as Douglas Fir, this softwood has a rather straight, pronounced grain that has a reddish brown tint to it and is moderately strong and hard for a softwood. Fir is most often used for construction building materials, however it’s inexpensive and can be used for certain aspects of furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain uniformly, so it’s best when used in projects that require a painted finish.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  

Woodworking tools at Highland Woodworking - shop our comprehensive tool selection for the best in woodworking tools. Our lines include woodworking hand tools & power tools, joinery jigs, The World's Safest Tablesaw and The Best Bandsaw Blade Selection. Along with woodworking tools from top tool brands, we stock the woodworking materials & supplies you need everyday. View all tools at Highland Woodworking home to over 10,000 Woodworking Tools or browse through our Woodworking Tools sub-categories below. Be sure to check out our Woodworking Tool Sale page where you will find special offers and tool deals.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.

About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.
On the money issue one`thing I did is find something that is fairly easy to make and easy to sell. I made kaleidoscopes to begin with and still whip up a batch if I need to buy wood or a new tool. A neighbor WW makes wooden condiment holders for restaurants. A good friends son worked his way thru college by making a certain bearing that they needed on his tiny lathe. Spend a month or so on $$$ stuff before doing the better stuff. 

Woodworker's Supply used to be my first choice. As a woodworking business owner I relied on their p...roduct availability and quick delivery. In 2018 they have failed repeatedly on both accounts-- everything is backordered, shipping has been incorrect after multiple assurances the problem will not happen again, backordered product is not shipped after in comes back in stock.
This is known as the “Scary Sharp” method and I first learned of it on Usenet back in the day. I’ve had pretty good luck only going up to 2000 grit automotive paper. That stuff is commonly available near the spraypaint at Wally-world. At this grit, I can easily shave the hair on my forearm. For a plate, I use a single 12×12 tile from a Big Box store.
For those who want to make money from their woodworking skills, David Piccuito's channel Make Something is a great place to start. He encourages woodworkers to use his designs for selling to clients as long as he gets credit for the design. Make Something has tutorials for making things at any skill level, from beginner to expert. It is filled with woodworking hacks on things like how to make curved inlays and how to drill really large holes—even those holes that are larger than your largest bit.
Add a little rustic décor to your walls by building a wooden mail sorter. Not only does this give you beautiful rustic décor, it also serves a very handy function by keeping mail neatly organized. You just need a few pieces of wood and some small coat hooks at the bottom to hang your keys. Stain it in any color you want and you have a very functional and very beautiful sorter.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
Build projects from wood the fast, strong, easy way using pocket-hole joinery and the Kreg Jig® R3. With the Kreg Jig, all you have to do is drill a hole in one of the pieces you want to join. Then drive in a Kreg Screw. The self-tapping tip draws the joint together and holds it tight, so you can create beautiful, durable projects quickly. The portable Kreg Jig R3 features two hardened-steel drill guides, built-in guides that make it easy to set up on a wide range of material thicknesses, and a clamp pad—all in a compact carrying case.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
×