Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.

I taught (teach) several aspects of "green woodworking" and related subjects, so I love your question. The buying and using of old tools is great...no matter the source. However, I have seen much frustration ensue over getting them adjusted, and "work ready." As often a beginner with limited budgets, also have limited traditional skill sets as well in understanding these tools and sharpening them. You must be patient with yourself, as tuning these old tools up will be very time consuming. Sharpening (and the proper tools of sharpening) should be your first acquisition. So many folks buy chickens before building a proper "chicken coop." Traditional tools are the same way, as there is no reason to own them, if you can't keep them properly honed.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
It's funny how some interests (or trades) got onto YouTube very early.  Woodworking has been popular on there since the video-sharing behemoth got started.  I suspect this is because the US has a strong tradition of TV shows about woodworking - two great examples being Norm Abram's New Yankee Workshop and Roy Underhill's Woodwright Shop.  With a plethora of channels available on cable, and a bigger population, broadcasters were able to air more niche, and thus detailed shows.   Over in the UK we had four channels, and so if something wasn't going to appeal to at least 5% of the population (or it was cultural) then it didn't stand a chance.  
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
While the router isn’t exactly necessary to build the most basic projects, it will really allow you to put that extra level of detail on a project so it isn’t quite so bland looking. Routers are also an extremely versatile tool that can be used in lieu of a jointer to get a straight edge on rough lumber, put a nice detail edge on a table top or piece of furniture, cut mortise and tenon joinery, cut dadoes and rabbets, mount in a table, or a countless number of other uses. Router bits can be pricey, so my advice would be to add bits as you need them for specific uses and projects. There are some variety pack kits available if you want a set to get started though. Also, there are smaller (trim) routers and full-size routers available. For the purpose of a beginner woodworking tool set, I recommend starting out with the small router and seeing just how much you can accomplish with that.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close

The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flat­tening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelo­gram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!   
Repurposed materials are taken from their original intent and utilized in another fashion. This refers to barn beams or siding, old wood floors, paneling or even wood pallets that had an original purpose, but are then transformed into something completely new. The possibilities are endless, as every repurposed piece has a little piece of history that comes along with it, and gives unbelievable character to the new project.
Being able to create and build a masterpiece from pieces of wood is more than a hobby -it’s a craft. Buying all the tools and supplies you need can start to add up to some serious money. But there are ways to enjoy building with wood without breaking your budget. Here’s a few woodworking tips that may get you started saving money and still being creative.
One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.
One of the most essential aspects of designing any custom piece is determining what type of raw material to use. This element will help to define the piece by assuring that you will get the look and feel that you want for your home or business. Whether it is traditional, rustic, farmhouse chic, industrial or a contemporary design, the material selected will help obtain that sense of style. More so, creativity and collaboration between the customer and CZ Woodworking will allow that raw material to come to life!

But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
×