You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house.  If you don’t have one, they are a few bucks each and WELL worth the investment.  AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
Pine is of the most common softwoods and comes in several varieties, including White, Knotty and Yellow – all of which can be used to make furniture. Pine is fairly easy to work with, as it is very soft, but it will show wear and tear more easily with everyday use (which could be a good or bad thing, depending on the look you prefer). Pine can either be stained or painted and often gives a more traditional feel to a piece – especially when using repurposed Pine flooring and siding. Pine is a practical and affordable choice for shelving, tables, closets, and cabinetry.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt.  Unfortunately, that ended up with the guy we hired stealing from us…..uggggh.  When will we ever learn to not be so trusting?!  Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!!  Sad.  Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
Since I long ago lost the woodcarving tools I used to own as a youth, I figured I would focus on something larger. With my current ideas of doing a commercial greenhouse venture, I have considered making my first project one of a pergola for training plants up as a living shade-tent area. I have also considered trying to do an earth-sheltered greenhouse assuming I can figure out a loophole in city ordinances and/or coax the officials to sign off on it. I would love to do some hand-carved bowls and eventually make my own workbench and maybe even craft other things like a shaving horse. A foot-powered lathe is another one that I still find fascinating from the Foxfire books.
About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
The problems  that we least expect.  Five years ago i purchased a bicycle and discovered while riding that I had developed balance problems.  I ignored the problem and stopped riding the bicycle.During this period I built a workshop in my basement and stocked with the best handtools.  My lifelong dream was to be an anarchist!  In February 2012 I started having episodes of more severe balance problems which resulted in hospitalization and extended nursing home rehabilitationl for six months. The diagnoses is Parkinson Disease which causes muscles to react to unwanted brain signals.  Needless to say the therapist ordered "no woodworking" period" because of the hazards associated with machines and sharp tools.  I presented my case that I did only handwork with hand tools.  The therapist answer was "NO!".  Now I'm confined to using a walker or wheel chair and reading how you all are enjoying the smell of sawdust.
One of the great furniture woods, Mahogany has a reddish-brown to deep-red tint, a straight grain, medium texture and is moderately hard. It takes stain very well, but looks great with even just a few coats of oil on it. For an even more distinguished look, exotic African Ribbon-Striped Mahogany adds amazing grain and texture elements to this already beautiful species of wood.
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.

After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 
Cherry is a very popular and an all-around great wood. Cherry stains and finishes beautifully, bringing out the natural figure in the grain of the wood. Cherry also ages beautifully, giving you a consistent look year after year. Cherry’s heartwood has a reddish-brown color to it, while the sapwood is almost white (we prefer to utilize mostly heartwood in our workshop). This is an excellent choice for almost any woodworking project, as Cherry is a solid wood choice all around.

About Youtuber I do woodworking projects, pallet projects, tool reviews, DIY projects and quick tips. A goal of mine (As a woodworker) is to build custom/ fine furniture. I also want to help & inspire others. The woodworking/DIY community is great!. I've learned quite a bit from other woodworkers and hope that others will learn from me too or at least get inspired to build something.
Brian Grella builds DIY woodworking projects in his garage woodshop. He lives by the motto "Cars Live Outside." Brian works in his garage to build useful household items like guitar stands, pizza cutters and breakfast trays. In one of his videos, Brian shows how he made salad tongs and then eats a salad right there on camera to show off his wooden creations.

About Youtuber My name is Andrei. I live in Russia and run my small business. Woodworking is my passion. I am the only woodworker in the shop. It is my full time job. I make only end grain cutting boards. I've been making end grain cutting boards for years. Sometimes I make end grain chessboards, end grain jewelry boxes, etc. Also I prepare woodworking plans.


On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
Ron Paulk is an extremely likeable mystery and I think he deserves 10x more subscribers than he has. I'm convinced he's a secret millionaire - he has a workshop in what seems to be the 20-car garage of a multi-million dollar mansion - which he claims belongs to a friend and he's only using it temporarily while they sell the house.  I think it's been five years now that he's been there.  But anyway, Ron is mainly a finish carpentry contractor - that's things like baseboard, fireplaces, kitchen cabinets etc.  He is a master craftsman.  What makes him unique is his approach to working - he is all about being portable, mobile and lightweight.  Every year he seems to fit out a new van or trailer as a mobile woodshop.  I've built Ultimate Workbench, Chop Saw station and fitted out a van following his designs.  He introduced me to Festool, which was a costly mistake for me!  I've built a lot of his projects, and I learned a whole lot along the way.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well. 

Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
One of the most heavily used tools in your shop will be your table saw.  It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs.  Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.  
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.   

Woodworking is a highly visual craft. There’s just something photogenic about lumber getting cut to size, dry-fit, glued or tacked together, and finally sanded down and finished into a beautiful piece of furniture. Even if you’re not a woodworker yourself, watching high-quality woodworking videos is a great way to learn about how stuff gets made, and who knows, you might even realize you want to make something yourself.
If you’d like to read some more about SketchUp, check out Ryan’s article on how to plan a home DIY project with SketchUp 3D Design for Daily Life: How to Plan a Home DIY Project With Sketchup 3D Design for Daily Life: How to Plan a Home DIY Project With Sketchup Doing a home improvement project on your own isn't always a simple matter. Sometimes it seems simple enough when you get started, but before you know it, you realize that if you had just taken... Read More . And if the idea of 3D design in general captivates your imagination, you should read our interview with world-class 3D artist Rafael Grassetti How A Dream Job Comes True: Interviewing World-Class 3D Artist Rafael Grassetti How A Dream Job Comes True: Interviewing World-Class 3D Artist Rafael Grassetti It's not every day that I get to pick the brain of a world-leading 3D artist -- but that's exactly what I got to do with Rafael Grassetti. You may not recognize Rafael's name, but... Read More .
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Improving an item with a Resin increases the effective item level by 3. For example, a white quality Oak Bow at level 16 will, once improved with Pitch, have an effective item level of 19. Improving it again with Turpen, will make the effective item level 22. You will notice in the Weapon and Armor tables that the Superior value at level 16 is the same as Normal at level 22. This is important to note, since several Crafted Sets have break points where their bonuses increase based upon "effective level".
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
×