Man, do I ever know about the "pre-buyers remorse"! My fiancé is a self proclaimed "cheapskate"(her language is a bit more coarse), but when it comes to my shop, she's all for me spending. I always end up being the one to pump the brakes, as I have a history of being TERRIBLE with money(@ 21, I was making close to 6 figures with no post-secondary education, and at 31, I still have less than $5,000 in the bank), while she pushes me to get "whatever I need". Of course, we all know that the line between want and need is pretty blurry. I agree with some of the other posts; I keep all of my expenses logged, and try to churn out money-makers to chip away at the red, always hoping to reach the black. So far, I'm still seeing red, but as my shop continues to flesh-out and my skill set grows, profit begins to sound more and more feasible all the time. Of course, I'm not really trying to make money. I just want to buy bigger and better equipment and supplies!
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Steve Ramsey. He's an energetic, fast-talking eccentric whose built his channel based on projects that can be done without investing in fancy tools. He trudges out a banged-up table saw from his garage, chops stuff up on the bed of his truck, and generally produces well-structured projects - even if I can't agree with his design aesthetic and color choices. Lots of good stuff to learn and a great channel for someone starting out.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteriously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.