While you have a decent starter shop, it's important to keep in mind the projects that your tools can handle.  You are going to want to focus on projects that don't require your stock to be ripped to a different dimensions than what you purchased it at.  You are currently only set up to do crosscuts with your miter saw.  So while you can turn an 8' 2x4 into two 4' 2x4s, your not going to be able to turn that same board into two 2x2s.    
For under $20 I am very impressed with the Bad Blade Carver by Kwik Tool.  Mounted in a 4.5″ grinder, it removes a ton of material quickly yet allows a fair amount of control.  The disk has only 6 teeth so the carver is mainly a solid disk with very few teeth to bite and create kick-back or dig-in. I found I had the best control when engaging the blade between 12 o’clock (top of the grinder) and 3 o’clock. When in that range it was not overly aggressive and left me in control.
Now, I’m not crazy rich or anything. I know that’s still a lot of money, but you will be able to make SO many things with just these five tools you seriously won’t believe it.  And if you are just starting out, just buy one tool and try it out. You’ll be surprised how much you can make with just a jigsaw,  hammer, nails and a screwdriver.  I made tons of stuff!  All you have to do is get started…where there is a will there is a way. 🙂
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Second, it is easier to learn to use hand tools on a solid bench than on a Workmate or some other modern clamping sawhorse.  The bench doesn't have to be expensive or large.  A 20" by 5' top will get you started.  Look at Chris Schwarz's second book on Workbenches "The Workbench Design Book" for ideas.  If you are a good scrounger you can recycle framing lumber from building teardowns to build a good bench for next to nothing.  A vise screw to make a leg vise is less than $60.
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!
In my experience, the best saws are the Japanese styles. They are very economical (less than $60 for a very high quality saw), easy to use because the cut on the pull stroke, and stay sharp for a long time. If I had to pick one, and only one saw, it would be a ryoba saw, which has rip teeth on one side and crosscut on the other, so its two saws in one.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk. 

Carl Jacobson has created over 350 videos to overwhelm you with project ideas, some of which you can complete in less than an hour. He takes you through the entire process from preparing the wood to the sanding and finishing of the project. Carl releases a new video every Friday with a follow-up video every Monday to answer questions based on the feedback he received over the weekend.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
Rob Cosman and Paul Sellers. Rob is damn near a genius when it comes to woodworking. He routinely comes up with methods and tools that sort of change the way we all do things in the shop. The guy is also an amazing instructor. Paul Sellers is also an amazing instructor. These are the kinds of guys that all the rest on your list learned how to woodwork from!
About Youtuber My name is Andrei. I live in Russia and run my small business. Woodworking is my passion. I am the only woodworker in the shop. It is my full time job. I make only end grain cutting boards. I've been making end grain cutting boards for years. Sometimes I make end grain chessboards, end grain jewelry boxes, etc. Also I prepare woodworking plans.
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.


Do you enjoy woodworking?  Do you have a budget that you have set aside just for your woodworking?  If you are not a millionaire, than more than likely you will have some sort of a budget.  Let me give you a little insight into why you are here and what you will find on this site.  Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job?  Or maybe you are wanting to turn your hobby into a full time job.  If that sounds like you than  your in the right place.
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.
These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects  to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge.  Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.

Over a year ago, I wrote up a round-up of three woodworking resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Few things are as satisfying and relaxing as making something new with your own hands. Programming comes close, at least for me (and I've recently offered some tips on learning to code), but it's still... Read More which included talented YouTube woodworkers Matthias Wandel, Steve Ramsey, and Marc Spagnuolo, AKA The Wood Whisperer. All three still produce wonderful work — and today I’d like to introduce you to five other YouTube woodworking channels worth following.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.

I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.

Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
Ash is a white to pale brown wood with a straight grain. It’s pretty easy to work with, is a fairly hard and dense wood, and takes to stain quite nicely. Ash has a medium to coarse texture similar to oak. The grain is almost always straight and regular, though sometimes moderately curly or figured boards can be found. Ash is becoming harder and harder to find, so it ranks as an increasingly expensive material to use.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
A long-established channel with Italian-American woodworking geek Marc Spagnoli and his sidekick Nicole.   It's filled with great tutorials, guides, reviews and generally high quality content.  I'd described as aimed at an improving, and committed, woodworker - he uses fairly lots of clamps and glue, and shows in professional how to build quality pieces, generally of furniture.  I learned a huge amount from here, and it's easy bedtime viewing.  
Cherry is a very popular and an all-around great wood. Cherry stains and finishes beautifully, bringing out the natural figure in the grain of the wood. Cherry also ages beautifully, giving you a consistent look year after year. Cherry’s heartwood has a reddish-brown color to it, while the sapwood is almost white (we prefer to utilize mostly heartwood in our workshop). This is an excellent choice for almost any woodworking project, as Cherry is a solid wood choice all around.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."

For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
About Youtuber Woodworking is my passion and I there is nothing I won't try to build, fix, or improve on my own. I got into woodworking and the passion has completely consumed me. Becoming a great woodworker and do it yourself-er is about finding the right information and creative solutions with the materials and skill sets available to you. I eagerly look forward to showing you how I accomplish my projects.
×