The directions that you'll find for making this Jack-o-lantern are found at HGTV, and they suggest using a battery operated votive to light up the lantern. I believe I'd try to figure out a way to add the "light" part of an inexpensive solar yard light instead. That way the jack-o-lantern would light as soon as it got dark. I wonder if that would work?
I have been around woodworking my entire life. I have always been intrigued by how you can take something like lumber and turn it into a wonderful, beautiful piece of furniture. Once I graduated high school, I kind of got out of woodworking. I wanted to go a different route. I was going to college and just trying to make ends meet on the bills.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
I started Woodworking Wednesdays because I thought my woodworking projects didn’t fit in very well with my UnbrokenFurniture.com blog. However, more and more, the furniture I’m making on that blog is handmade reclaimed wood furniture. This has sort of made this blog redundant. I’m not putting out enough furniture pieces to populate both blogs, so I’m going to stop posting those here.
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.
One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
I use a 9″ x 12″ Chinese grade B surface plate and wet the back of the carborundum “sandpaper” to hold it in place. Obviously not the “budget” version, but I have the surface plate for other purposes. At about $17 from ENCO it wasn’t very expensive. And it *really* is flat to better than 0.001″. So the thickness of the paper is the biggest error. I also have a good assortment of Arkansas and other types of stones, though none of the Japanese waterstones. I generally don’t use the surface plate unless the edge is really bad e.g. an abused tool picked up at a yard sale.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
Just how small? Will you have an extra bedroom for your shop or will you be doing woodworking in your living room? Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time? A while back FWW had a video tour of a shop in Japan that was smaller than small. I'll try to find it and get back. Found it... shows what can be done in a small space but this shop was not on a small budget so no help there.