Woodworker’s Hardware is your one-stop online woodworker’s store for all of your woodworker's supplies. Shop for everything you need to start and finish your woodworking projects. Find a huge selection of hardware products including drawer slides, barn door hardware, lazy susans, kitchen cabinet hardware & accessories, and furniture hardware. We stock thousands of door and cabinet hardware and accessories like knobs, pulls, and hooks for kitchens, bathrooms, and closets. As one of the leading online kitchen cabinet hardware suppliers, shop for soft-close ball bearing drawer slides from top-rated brands like KV and Blum. Check out our sales page for our best offers! Our fully stocked warehouse full of woodworker’s supplies ensures shipping in 24 business hours.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
About Youtuber My name is Andrei. I live in Russia and run my small business. Woodworking is my passion. I am the only woodworker in the shop. It is my full time job. I make only end grain cutting boards. I've been making end grain cutting boards for years. Sometimes I make end grain chessboards, end grain jewelry boxes, etc. Also I prepare woodworking plans.
We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
Do you enjoy woodworking? Do you have a budget that you have set aside just for your woodworking? If you are not a millionaire, than more than likely you will have some sort of a budget. Let me give you a little insight into why you are here and what you will find on this site. Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job? Or maybe you are wanting to turn your hobby into a full time job. If that sounds like you than your in the right place.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
I wanted to have numerous outlets, and have enough electrical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
Just like a hammer and tape measure, a drill is something a lot of people already keep on hand for small household projects. Danny and I started out on a SUPER cheap drill when we first got married and quickly learned that this was not something to cheap out on. If you plan to do much woodworking, invest in a quality drill. It doesn’t have to be the best of the best, but do at least get a mid-grade drill.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email firstname.lastname@example.org and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
Use the square and position the pivot point onto the board top and slide the square up to the 5 on the line up “COMMON TOP CUT” outside the board. Mark the line as for the angle. After first angle is cut, measure the rafter length from the tip cut to get the seat cut measurement. Mark the seat cut and place the pivot point onto this mark and do the same step to get 5/12 angle. From that angle, measure up 2 ½” and make the line.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!