I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate.  So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it.  I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.

To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.

If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools.  It is sort of an inexpensive crash course in hand tools.  Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read.  Use the internet to learn all you can about a tool before buying.  The tools you need are dictated by what you want to build.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.

Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.

about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
I, too, would pass on the Jawhorse, and agree with the suggestion of a solid bench. (Remember, it can double as a desk if space is limited.)  A used solid-core door can be a starting point, but there are better options, such as laminating your own from scrounged 2x4s. Spending time at flea markets looking for old tools that can be reconditioned is a good suggestion, too.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
Ron Paulk is an extremely likeable mystery and I think he deserves 10x more subscribers than he has. I'm convinced he's a secret millionaire - he has a workshop in what seems to be the 20-car garage of a multi-million dollar mansion - which he claims belongs to a friend and he's only using it temporarily while they sell the house.  I think it's been five years now that he's been there.  But anyway, Ron is mainly a finish carpentry contractor - that's things like baseboard, fireplaces, kitchen cabinets etc.  He is a master craftsman.  What makes him unique is his approach to working - he is all about being portable, mobile and lightweight.  Every year he seems to fit out a new van or trailer as a mobile woodshop.  I've built Ultimate Workbench, Chop Saw station and fitted out a van following his designs.  He introduced me to Festool, which was a costly mistake for me!  I've built a lot of his projects, and I learned a whole lot along the way.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
@jayemel: tempered glass works perfectly, as the (theoretical) fluctuations in flatness as a result of inner stress are several orders of magnitude smaller than the significant variations of thickness of your sandpaper. Unless you want to reflect the light of distant galaxies off the bevel of your chisel and measure their red-shift, you will be fine (and safer) to use tempered glass.

Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE


Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
While I am admittedly still new to the wonderful world of woodworking, I can't help but feel that one of the contributing issues/factors responsible for my prolonged progress in starting/finishing projects is how I've become accustomed (more like "trained") - fortunately or unfortunately, depending how you look at it - to work within a financial budget.
One of the great furniture woods, Mahogany has a reddish-brown to deep-red tint, a straight grain, medium texture and is moderately hard. It takes stain very well, but looks great with even just a few coats of oil on it. For an even more distinguished look, exotic African Ribbon-Striped Mahogany adds amazing grain and texture elements to this already beautiful species of wood.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  

Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.


Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall

I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.

This is sequential to step one, but with a little difference. You choose simple and easy woodcrafts to make.  Ones that do not require investment in expensive tools. Nor do they require a lot of wood and raw materials. There are plenty of examples of such projects to be found. We have written about a few of them here. Small and popular wood projects can be made in large numbers and sold with ease, for a high profit. 
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
There are and they are considerably cheaper. I found a pair of glue brushes on Amazon for less than half the price of a singles dedicated glue brush. I tested them out on a recent gluing and they work well for spreading glue and getting it into dovetails and mortises. When you are done you can either run the brush underwater to clean it or wait until the glue dries the pluck it off the bristles with a few easy pulls. The glue comes right off the silicone bristles.
For many tasks you may not gain much benefit from going above 4-500 grit but polishing your axe to 0.33 micron certainly won’t affect edge retention. For finishing work, you certainly do want as well polished of an edge as possible since that means less scraping or sanding. A well honed plane can leave a surface that’s actually too smooth for painting.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
So I am curious about what the best choices in woodworking tools would be for someone who is just beginning to develop the skills involved with the craft. Funds would be limited and at least for me, I have a strong preference for non-electric tools when possible. Not only what would be the best tools to start a collection with, but also what would be a good way to obtain them aside from ebay, pawn shops and antique shops?

If you’ve been reading my regular blog, unbrokenfurniture.com, then you already know that I’m a novice furniture upcycler. Up until now I’ve been repairing and refinishing existing furniture. Lately I’ve been picking up more and more reclaimed wood and other raw materials, so I’ve decided to learn to build some furniture from scratch. Because building furniture from scratch doesn’t really fit with the theme of unbrokenfurniture.com, I’ve decided to keep these projects on a separate space, hence woodworkingwednesdays.com was born. I’m planning to post one new project each week (hopefully Wednesday).


Woodworking tools at Highland Woodworking - shop our comprehensive tool selection for the best in woodworking tools. Our lines include woodworking hand tools & power tools, joinery jigs, The World's Safest Tablesaw and The Best Bandsaw Blade Selection. Along with woodworking tools from top tool brands, we stock the woodworking materials & supplies you need everyday. View all tools at Highland Woodworking home to over 10,000 Woodworking Tools or browse through our Woodworking Tools sub-categories below. Be sure to check out our Woodworking Tool Sale page where you will find special offers and tool deals.
Fine Woodworking Tools and Supplies at Highland Woodworking – make us your woodworking tool supply source. Woodworking Hand Tools are one of our passions at Highland Woodworking so we sell the very best hand tool brands in production today. Handmade, high quality hand tool lines such as Auriou Rasps, Barr Forged Tools, Gransfors Axes, Lie Nielsen Tool Works, Woodpeckers Precision Tools and numerous other fine hand tool makers. We love fine Woodworking Power Tools too, so we sell Festool Power Tools and SawStop - the best power tool brands for woodworking. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools, equipment & supplies.
×