We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time. It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years. During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
If you’ve been reading my regular blog, unbrokenfurniture.com, then you already know that I’m a novice furniture upcycler. Up until now I’ve been repairing and refinishing existing furniture. Lately I’ve been picking up more and more reclaimed wood and other raw materials, so I’ve decided to learn to build some furniture from scratch. Because building furniture from scratch doesn’t really fit with the theme of unbrokenfurniture.com, I’ve decided to keep these projects on a separate space, hence woodworkingwednesdays.com was born. I’m planning to post one new project each week (hopefully Wednesday).
Ron Paulk is an extremely likeable mystery and I think he deserves 10x more subscribers than he has. I'm convinced he's a secret millionaire - he has a workshop in what seems to be the 20-car garage of a multi-million dollar mansion - which he claims belongs to a friend and he's only using it temporarily while they sell the house. I think it's been five years now that he's been there. But anyway, Ron is mainly a finish carpentry contractor - that's things like baseboard, fireplaces, kitchen cabinets etc. He is a master craftsman. What makes him unique is his approach to working - he is all about being portable, mobile and lightweight. Every year he seems to fit out a new van or trailer as a mobile woodshop. I've built Ultimate Workbench, Chop Saw station and fitted out a van following his designs. He introduced me to Festool, which was a costly mistake for me! I've built a lot of his projects, and I learned a whole lot along the way.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.