About Youtuber LAB11 Created designer furniture from scratch from wood and recycled materials like pallets or customizes and repairs existing furniture. The watchwords for our creations and customizations are: Pretty, durable and solid things. Here are the videos of some projects creations but also of layout of the workshop, A video per month out at least.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Ash is a white to pale brown wood with a straight grain. It’s pretty easy to work with, is a fairly hard and dense wood, and takes to stain quite nicely. Ash has a medium to coarse texture similar to oak. The grain is almost always straight and regular, though sometimes moderately curly or figured boards can be found. Ash is becoming harder and harder to find, so it ranks as an increasingly expensive material to use.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
If you'd like to learn more about the differences between hardwood species, I can think of no better resource than R. Bruce Hoadley's 1980 masterpiece, Understanding Wood: A Craftsman's Guide to Wood Technology. Not only does Hoadley detail nearly every species used for woodworking, he does an exceptional job at describing how to prepare, work with and finish these hardwoods. This is an industry-standard resource, one that I'd highly recommend to every woodworker.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
here are thousands of wood species in the world, and hundreds of them are commonly used for woodworking. Additionally, there are dozens of "wood products" that are made from wood for construction and metal hardware designed specifically for woodworking projects. To make the wisest possible choices, you should know not only what is available to you, but how it is prepared.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
If you’ve been reading my regular blog, unbrokenfurniture.com, then you already know that I’m a novice furniture upcycler. Up until now I’ve been repairing and refinishing existing furniture. Lately I’ve been picking up more and more reclaimed wood and other raw materials, so I’ve decided to learn to build some furniture from scratch. Because building furniture from scratch doesn’t really fit with the theme of unbrokenfurniture.com, I’ve decided to keep these projects on a separate space, hence woodworkingwednesdays.com was born. I’m planning to post one new project each week (hopefully Wednesday).
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on. The rewards aren't usually good enough to compel me to purchase on their own. But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
Matthias Wandel loves himself some precision engineering. His craftsmanship is great, but he's more a Da Vince for his contraptions. He tends to build his own tools, and he's very much a function over form guy. There's geekery aplenty with maths, physics and all sorts of CAD wackiness - feast your eyes on the marble machines! All seemingly done on a shoestring budget. Genius is the word for Matthias.
Pine is of the most common softwoods and comes in several varieties, including White, Knotty and Yellow – all of which can be used to make furniture. Pine is fairly easy to work with, as it is very soft, but it will show wear and tear more easily with everyday use (which could be a good or bad thing, depending on the look you prefer). Pine can either be stained or painted and often gives a more traditional feel to a piece – especially when using repurposed Pine flooring and siding. Pine is a practical and affordable choice for shelving, tables, closets, and cabinetry.
The level of sophistication in a $250 shop is significantly less than a $2,500 shop. But keep in mind even a $2,500 budget is entry level. Acquiring a shop full of the perfect tools for each and every job takes a life time. But that doesn't mean that producing quality work takes a lifetime. One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
These basics are going to set you back about $180, leaving you with $320 left to work with. We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives. This should lead to more consistent results, more enjoyable builds, and increased efficiency. These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.