Ash is a white to pale brown wood with a straight grain. It’s pretty easy to work with, is a fairly hard and dense wood, and takes to stain quite nicely. Ash has a medium to coarse texture similar to oak. The grain is almost always straight and regular, though sometimes moderately curly or figured boards can be found. Ash is becoming harder and harder to find, so it ranks as an increasingly expensive material to use.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
To get the most out of your router, you are going to want a router table. You may find yourself asking if you really need one - if you do, check this post out. It's one of those purchases that you won't truly understand how valuable it is until you have one. Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150). If you want to see our favorite tables along with write-ups, check them out here.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound system and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
Well there it is, my top 5 list of the best beginner woodworking tools. Let me know your thoughts or some of your favorite tools for each category. Of course this isn’t an all-encompassing list, there are all of the little extras like tape measure, square, clamps, glue, etc. To see what I use for all of these options check out the complete list of tools from my shop.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key storage, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
The level of sophistication in a $250 shop is significantly less than a $2,500 shop. But keep in mind even a $2,500 budget is entry level. Acquiring a shop full of the perfect tools for each and every job takes a life time. But that doesn't mean that producing quality work takes a lifetime. One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
The solution to potentially wedged boards on a jointer is to add a planer to the mix. A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface. This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square. As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.