An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.

Use the square and position the pivot point onto the board top and slide the square up to the 5 on the line up “COMMON TOP CUT” outside the board. Mark the line as for the angle. After first angle is cut, measure the rafter length from the tip cut to get the seat cut measurement. Mark the seat cut and place the pivot point onto this mark and do the same step to get 5/12 angle. From that angle, measure up 2 ½” and make the line.


 here are thousands of wood species in the world, and hundreds of them are commonly used for woodworking. Additionally, there are dozens of "wood products" that are made from wood for construction and metal hardware designed specifically for woodworking projects. To make the wisest possible choices, you should know not only what is available to you, but how it is prepared.	

The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.

In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
Do you enjoy woodworking?  Do you have a budget that you have set aside just for your woodworking?  If you are not a millionaire, than more than likely you will have some sort of a budget.  Let me give you a little insight into why you are here and what you will find on this site.  Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job?  Or maybe you are wanting to turn your hobby into a full time job.  If that sounds like you than  your in the right place. 

When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
×