A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel. The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece. Having control over both angles allows much easier cuts of trims and moldings. It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
About Youtuber Steve Johnson is a full time life-long hobbyist woodworker committed to helping new and experienced woodworkers achieve the "shop of their dreams" - even if (especially if?) they don't have a dream budget to work withHis videos can be seen at "DownToEarthWoodworks" on YouTube and his articles appear monthly in Highland Woodworking's on line newsletter "Wood News Online.".
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
There are some basic things every woodworker needs to get started. Assuming you aren't the kind of person that does everything with hand tools, you'll first need a drill. Power drills come in many different styles and price ranges. The popular trend right now is for companies to make cordless tool systems that all run off of the same battery packs, and a drill is often the first tool a person gets in the set. Cordless drills are popular and handy for doing household tasks , such as hanging picture frames; but for serious woodworking, they can lack power and might die in the middle of a job. Corded drills are a less expensive option and often work better for the tasks you'll be doing in a wood shop; just get a cheap extension cord to go with it. You can easily find a corded drill of good quality for about $100.
About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living in a great craft. My hat is off to all of you.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws. Because of this, I'd stick to the two saws we looked at in the $500 build: The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110. These two additions bring our running total to just over $500.
I use a 9″ x 12″ Chinese grade B surface plate and wet the back of the carborundum “sandpaper” to hold it in place. Obviously not the “budget” version, but I have the surface plate for other purposes. At about $17 from ENCO it wasn’t very expensive. And it *really* is flat to better than 0.001″. So the thickness of the paper is the biggest error. I also have a good assortment of Arkansas and other types of stones, though none of the Japanese waterstones. I generally don’t use the surface plate unless the edge is really bad e.g. an abused tool picked up at a yard sale.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
My final suggestion is to use tape. I know this might seem crazy at first, but when gluing corners, tape comes in very handy. The secret is to tape up the outside of the corner when the boards are sitting flat, and then to apply the glue and bend the wood into the proper position. Then you simply use tape to hold the piece in place. This strategy works exceptionally well when gluing a box.
To get the most out of your router, you are going to want a router table. You may find yourself asking if you really need one - if you do, check this post out. It's one of those purchases that you won't truly understand how valuable it is until you have one. Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150). If you want to see our favorite tables along with write-ups, check them out here.
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
Then there are the “practical” woodworkers that enjoy weekend projects and things that don’t require a ton of expensive tools, time, and expertise (HELLO, THAT’S ME). I will be in the latter category. Sure, you can invest in hand tools, but in the words of one of my favorite internet sensations, “ain’t nobody got time fo that.” Let’s be practical here.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
For under $20 I am very impressed with the Bad Blade Carver by Kwik Tool. Mounted in a 4.5″ grinder, it removes a ton of material quickly yet allows a fair amount of control. The disk has only 6 teeth so the carver is mainly a solid disk with very few teeth to bite and create kick-back or dig-in. I found I had the best control when engaging the blade between 12 o’clock (top of the grinder) and 3 o’clock. When in that range it was not overly aggressive and left me in control.
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap. ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15). 1 rip handsaw (used ones can be found at Antique stores for $20 or less. Try to find one that is fairly sharp to start with). Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both). A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.
@jayemel: tempered glass works perfectly, as the (theoretical) fluctuations in flatness as a result of inner stress are several orders of magnitude smaller than the significant variations of thickness of your sandpaper. Unless you want to reflect the light of distant galaxies off the bevel of your chisel and measure their red-shift, you will be fine (and safer) to use tempered glass.
By the way, before you yell at me about the fact that the price on the links for the nail gun is more than $200, listen up I have a handy tip: There are sales throughout the year on this exact package for $200. That’s how I bought mine. Just keep checking back. And be sure to follow me on social media. I keep checking it, too and if I see it’s on sale, I will post it to let you all know!
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!