I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
As the mother of 4 children, 3 of whom are busy boys, much of Jen's free time is spent at the ball field, brushing up on video game terminology and building Lego towers. Jen is the owner and creative mind behind Banner Events. With a passion for event planning & party styling and an obsession with the little details that take an event from ordinary to extraordinary, Jen wakes up every morning excited to get to work.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
While you have a decent starter shop, it's important to keep in mind the projects that your tools can handle. You are going to want to focus on projects that don't require your stock to be ripped to a different dimensions than what you purchased it at. You are currently only set up to do crosscuts with your miter saw. So while you can turn an 8' 2x4 into two 4' 2x4s, your not going to be able to turn that same board into two 2x2s.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
About Youtuber Steve Johnson is a full time life-long hobbyist woodworker committed to helping new and experienced woodworkers achieve the "shop of their dreams" - even if (especially if?) they don't have a dream budget to work withHis videos can be seen at "DownToEarthWoodworks" on YouTube and his articles appear monthly in Highland Woodworking's on line newsletter "Wood News Online.".
I’m going to find a different piece of metal, and I’ll post a video of the working track when it’s done. I bet some of you are coming to expect failure from this blog. I warned you in the beginning that I’m new to this. I’m trying to share my experience from both my successes and my failures. It just so happens that I have a lot more failures so far.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
Just how small? Will you have an extra bedroom for your shop or will you be doing woodworking in your living room? Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time? A while back FWW had a video tour of a shop in Japan that was smaller than small. I'll try to find it and get back. Found it... shows what can be done in a small space but this shop was not on a small budget so no help there.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.