That just reminded me of a FWW piece many years ago that had me rolling on the floor. Craftsman had built a large piece being delivered to an apartment on the top floor. Couldn't get it on the elevator so they got controll of the elevator and ran the top of it to be even with the floor, loaded the piece on the top of the car and rode with it inside the shaft while balancing it and keeping it from hitting the shaft walls. At some point in the trip up they lost control of the elevator and it started making trips up and down to other floors. I'll see if I can find it.
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.
Buying rough cut lumber saves a ton of money. Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber. Let's look at an example: I'm going to build a table that will require 50 board feet of oak. If I buy finished oak it will cost around $5.5 / bf or $275. Alternatively, I can buy rough cut oak at $1.25/bf or ~$65. In this one project I've saved $210. That's enough for a new power tool.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
If you choose paint for your finish, you won't want to waste your money on woods known for their color and beauty when stained, so avoid richly-colored species such as oak, maple, walnut or mahogany. For painted projects, poplar is a very good choice because it is relatively stable and takes paint quite well (not to mention that it doesn't look all that good stained).
Another example is lathe tooling or metal gravers which are routinely polished on fine agate stones and these don’t chip or roll an edge unless abused. These are one of the times where a jig is a requirement for reproducible results and a couple degrees off the recommended angle can make a difference. For a wood work, a couple degrees either way won’t really be noticed.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
My final suggestion is to use tape. I know this might seem crazy at first, but when gluing corners, tape comes in very handy. The secret is to tape up the outside of the corner when the boards are sitting flat, and then to apply the glue and bend the wood into the proper position. Then you simply use tape to hold the piece in place. This strategy works exceptionally well when gluing a box.
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Mitre Block/Box for Cutting Coving Skirting Boards Polypropylene mitre box for accurate cutting of mitres and butt joints. Colours may vary from image shown. Stock No: 633731 EAN: 5055058172877 External Size: LxWxD = 300x140x75mm Internal Size : LxWxD = 300x105x58mm Colour: May Vary: Image is for illustration purposes only. Manufacturer: Silverline.