You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Copyright © 2018 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
I Like to Make Stuff is the perfect channel for beginners who want comprehensive teaching on woodworking. It has a show called Maker 101 that goes into the basic skills you need to start making stuff. I Like to Make Stuff is not intimidating to the beginner because it isn’t afraid of showing woodworkers making mistakes on their project rather than always doing everything perfectly.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate.  So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it.  I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.

I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound sys­tem and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!


However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
×