Over a year ago, I wrote up a round-up of three woodworking resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Learn To Build Your Own Furniture With These Impressive Carpentry & Woodworking Resources Few things are as satisfying and relaxing as making something new with your own hands. Programming comes close, at least for me (and I've recently offered some tips on learning to code), but it's still... Read More which included talented YouTube woodworkers Matthias Wandel, Steve Ramsey, and Marc Spagnuolo, AKA The Wood Whisperer. All three still produce wonderful work — and today I’d like to introduce you to five other YouTube woodworking channels worth following.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40. A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits. As you work on a few projects you may find that more specialized bits are needed. But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house. If you don’t have one, they are a few bucks each and WELL worth the investment. AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂
Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Only comment would be to start with manual machines -once you have them mastered, then worry about CNC. I'm only 71 at this point, but I still have a lot of things left to master! Try to find even a HF mini-lathe and mill used, and get started. The sooner you start, the sooner you become experienced, Just a warning though - machining is just as addictive as wood working.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on. The rewards aren't usually good enough to compel me to purchase on their own. But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Birch is readily available and less expensive than many other hardwoods. Birch is stable and easy to work with. However, it’s hard to stain because it can get blotchy, so it is generally preferred to paint Birch.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate. So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it. I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
@jayemel: tempered glass works perfectly, as the (theoretical) fluctuations in flatness as a result of inner stress are several orders of magnitude smaller than the significant variations of thickness of your sandpaper. Unless you want to reflect the light of distant galaxies off the bevel of your chisel and measure their red-shift, you will be fine (and safer) to use tempered glass.