About Youtuber Have you ever considered woodworking as a hobby but didn't where to begin? Tune in for this video series from the editors of Fine Woodworking magazine, and we'll guide you through the process. From choosing your first tools to setting up a workspace to completing your first woodworking projects, you'll discover just how easy it is to get started in woodworking.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.

Ron Paulk is an extremely likeable mystery and I think he deserves 10x more subscribers than he has. I'm convinced he's a secret millionaire - he has a workshop in what seems to be the 20-car garage of a multi-million dollar mansion - which he claims belongs to a friend and he's only using it temporarily while they sell the house.  I think it's been five years now that he's been there.  But anyway, Ron is mainly a finish carpentry contractor - that's things like baseboard, fireplaces, kitchen cabinets etc.  He is a master craftsman.  What makes him unique is his approach to working - he is all about being portable, mobile and lightweight.  Every year he seems to fit out a new van or trailer as a mobile woodshop.  I've built Ultimate Workbench, Chop Saw station and fitted out a van following his designs.  He introduced me to Festool, which was a costly mistake for me!  I've built a lot of his projects, and I learned a whole lot along the way.


About Youtuber This channel is created to share my passion for woodworking and guide beginners into realizing the joy of this hobby. Woodworking is fun, inspiring and helps you to design, create and relax. You can pick up a piece of wood and create something out of it and the result is uplifting. You just created something valuable from piece of wood.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
About Youtuber LAB11 Created designer furniture from scratch from wood and recycled materials like pallets or customizes and repairs existing furniture. The watchwords for our creations and customizations are: Pretty, durable and solid things. Here are the videos of some projects creations but also of layout of the workshop, A video per month out at least.

About Youtuber Woodworking is my passion and I there is nothing I won't try to build, fix, or improve on my own. I got into woodworking and the passion has completely consumed me. Becoming a great woodworker and do it yourself-er is about finding the right information and creative solutions with the materials and skill sets available to you. I eagerly look forward to showing you how I accomplish my projects.
Do you enjoy woodworking?  Do you have a budget that you have set aside just for your woodworking?  If you are not a millionaire, than more than likely you will have some sort of a budget.  Let me give you a little insight into why you are here and what you will find on this site.  Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job?  Or maybe you are wanting to turn your hobby into a full time job.  If that sounds like you than  your in the right place.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  
My first projects were making things from pallet boards. I cut the boards to size using my jig saw.  It’s not quite as good as using a miter saw, but it got me by for a while with sufficient results.  Even now that I have a miter saw, I still use my jig saw A LOT to make notches (like for my outdoor table), or fun designs (like these deer heads last Christmas).
The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.

As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.


Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.

We’ve already done rope, and now we’re on to another rustic material we love: wood! It’s as basic of a material as clay and is constantly reinvented by DIYers, crafters, artists, hackers, and carpenters. To get inspired to create our own batch of cool wooden objects, we turned to our favorite fellow makers to see what projects they’ve come up with. Scroll down for our top DIY wood project picks.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.
This is known as the “Scary Sharp” method and I first learned of it on Usenet back in the day. I’ve had pretty good luck only going up to 2000 grit automotive paper. That stuff is commonly available near the spraypaint at Wally-world. At this grit, I can easily shave the hair on my forearm. For a plate, I use a single 12×12 tile from a Big Box store.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
×