I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
Another staple in the beginner woodworkers tool kit has to be the cordless drill. Used for either drilling holes or driving fasteners, this tool gets used on almost every project. There a tons of options here regarding size of batteries, aka power, but something around the 18-20 volt range is a good all-around size that will not leave you constantly wishing you had something larger or smaller. Here is a large accessory kit at a good price that should give you most of the drivers a bits you will need.
Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house.  If you don’t have one, they are a few bucks each and WELL worth the investment.  AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.

You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
Add a little rustic décor to your walls by building a wooden mail sorter. Not only does this give you beautiful rustic décor, it also serves a very handy function by keeping mail neatly organized. You just need a few pieces of wood and some small coat hooks at the bottom to hang your keys. Stain it in any color you want and you have a very functional and very beautiful sorter.
Some might expect to see a cordless drill on this list, but when we're talking about basic power woodworking tools, a corded drill is more versatile and powerful. Sure, the cordless is, well, cordless, which makes it more portable, but corded drills are less expensive and can do more than a cordless drill. There are some options to consider when choosing a corded power drill, such as whether you want a 3/8-inch or 1/2-inch chuck, keyed or keyless chuck, straight drill or hammer drill, and so on. Learn all about these options (along with some suggestions on what to look for when shopping) in this article on corded power drills.

If you’ve been reading my regular blog, unbrokenfurniture.com, then you already know that I’m a novice furniture upcycler. Up until now I’ve been repairing and refinishing existing furniture. Lately I’ve been picking up more and more reclaimed wood and other raw materials, so I’ve decided to learn to build some furniture from scratch. Because building furniture from scratch doesn’t really fit with the theme of unbrokenfurniture.com, I’ve decided to keep these projects on a separate space, hence woodworkingwednesdays.com was born. I’m planning to post one new project each week (hopefully Wednesday).
Of course she was probably going easy on the driver.  Wouldn't have been pretty if my little angel had got her delicate little hammer wielding, ( that was pretty much before nail guns ), wrench turning, Judo throwing fallangies on him.  Did I mention my surfer girl's best girl friend was a black belt (and raced bicycles on an international olympic level )?
Well there it is, my top 5 list of the best beginner woodworking tools. Let me know your thoughts or some of your favorite tools for each category. Of course this isn’t an all-encompassing list, there are all of the little extras like tape measure, square, clamps, glue, etc. To see what I use for all of these options check out the complete list of tools from my shop.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.

A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close


Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
I cannot think of a project that the orbital sander was not used. Whether painting, staining, or just applying a clear finish, you will want to sand to some level to smooth out the wood. Even when using barn-wood or reclaimed wood, I often at least sand the edges to get rid of sharp edges and revel some of the underlying fresh wood. I usually have about 4 or 5 different grit sandpaper on hand for my orbital sander, here is my favorite brand.
Eastern Hemlock, the state tree of Pennsylvania, is a softwood that has a naturally light-reddish-brown color. Although Western Hemlock (sourced from the Pacific Northwest) is often used in furniture building due to its straight grain and finer texture, which sands to a silky, reflective smooth surface. Hemlock gives some hardwoods a run for their money in terms of durability and strength, but at a more approachable price point. Reclaimed Hemlock has made its way into local salvage yards in recent years, and is being utilized in all aspects of woodworking and furniture building.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
[…] Technically this is not a DIY video; it goes by very fast and there are no narrated instructions. That is because it was put together to promote a finished product available here dfmmc.com. But if you have experience welding, it is not all that hard to follow along and figure out the steps and write them down. I might get lazy and buy one … but I love making things, so I definitely will be giving it a try. Whether you buy one ready-made or weld your own, I hope you love this rack as much as I do. What an awesome discovery! If you love rustic decorating you must check out our 85 Rustic storage projects and 40 Rustic home decorating ideas. […]
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.

At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!
Understand the pain. Retired, fixed income, bills to pay like anyone else. Most of the accumulated equipment is used, a few pieces bought new. Other detriment - WW is one hobby, home machining another, and welding/fabricating another, to say nothing of an electronics hobby. Add in no real shop, just enough garage space to house everything, and wheel each piece out on the drive to use. Bad weather = no work! Make a lot of my own stuff also, such as:
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
I just do it. Lol. Most of my projects are for my wife so its easier to scrape money together then listen to complaints about them not getting done! Seriously though, its tough. I have two expensive hobbies......woodworking and bass fishing, latter of the two being the worst. I reserve all my side work money for the two. One thing that helps is owning our own saw mill, lumber is basically free other then time.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.

If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
The Jay's Customs Creations YouTube channel releases weekly videos on shop projects and dimensional lumber projects. Jay's show can really help you if you want to do DIY woodworking projects on a budget. He sometimes shows viewers how to complete the project without electricity and using only hand tools. He goes over the prices he paid for materials to give people a realistic budget for the project before they get started.
My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.

A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
Danish Oil is an oil-based finish that soaks deep into wood pores to provide protection from the inside out. Generally made from a unique blend of penetrating oil and varnish that stains, seals and protects all at the same time, it enhances the natural look and feel of the wood, and creates the rich, warm glow. This finish is ideal for furniture, trim, molding or any other bare wood interior surface that calls for an accentuated look.
One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
here are thousands of wood species in the world, and hundreds of them are commonly used for woodworking. Additionally, there are dozens of "wood products" that are made from wood for construction and metal hardware designed specifically for woodworking projects. To make the wisest possible choices, you should know not only what is available to you, but how it is prepared.
About Youtuber Tom Fidgen is an author, musician, designer/maker living in Toronto, Ontario.He is the owner and lead instructor of The Unplugged Woodshop- Toronto, Canada's first, hand tool only woodworking school.Tom has written for Fine Woodworking Magazine, Popular Woodworking Magazine, Canadian Woodworking Magazine, Furniture & Cabinet Making Magazine, British Woodworking Magazine, as well as the Lee Vall.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
How would you like to look over the shoulder of a master builder inside his workshop to see how he does it? Not everybody wants a teacher walking them through their methods and reasons—they just want to see how a master working at his craft. Jimmy DiResta has been doing woodworking projects for over 40 years. He has a YouTube channel without any of the chatting you find on most other channels. Watching his videos, which are released bimonthly, you will only hear the sounds of the tools and not the sound of his voice.
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have chal­lenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Not only is having a full time job is hard to do woodworking, if you have a family as well, then that is another thing that you are going to have to juggle as well.  For me its a no brainer.  I always choose my family over my hobby of woodworking.  But when my family or job does not need my presence, that’s when I am free to let my brain just run loose on new ideas of what to build next.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
Of course she was probably going easy on the driver.  Wouldn't have been pretty if my little angel had got her delicate little hammer wielding, ( that was pretty much before nail guns ), wrench turning, Judo throwing fallangies on him.  Did I mention my surfer girl's best girl friend was a black belt (and raced bicycles on an international olympic level )?
As far as advice goes, I'm like a lot of the other folks on this thread; make a shop budget that fits into your existing budget and stick to it. Whenever you can foresee a larger expense, skrimp and save, cut costs in other areas of non-essential spending, and accept that sometimes, you NEED to go outside of your budget. In my experience, if it means enough to you, you can make it work. Good luck!
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."

Although we focus primarily on the use of wood in our work, CZ Woodworking also incorporates materials other than solid wood into our workshop. We work with metalworkers, glass companies, designers and artisans alike to bring various materials together to create custom pieces. Examples of additional materials we use are wrought iron, steel, glass, stone and more. By combining various mediums together, we are able to achieve the specific look that fits your needs best. Please contact us directly to inquire further.

The Jay's Customs Creations YouTube channel releases weekly videos on shop projects and dimensional lumber projects. Jay's show can really help you if you want to do DIY woodworking projects on a budget. He sometimes shows viewers how to complete the project without electricity and using only hand tools. He goes over the prices he paid for materials to give people a realistic budget for the project before they get started.
×