How about a hunk of butcher block counter top on a 4X4 (legs) base on locking wheels.  Round over the good side and it is a rolling kitchen stand - chopping block -  island.  Flip the top over, lock the wheels, and it's a bench.  There is a vise that is sold by Woodcraft that drops onto a mounted post in both vert and horiz positions that would be perfect for a small flip top bench.  The post would be mounted to the underside, unseen till the top was flipped and the vise dropped on.  It pivots but when the jaws are clamped it is tight.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.

The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close


About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.
As a gardener/homesteader, and setting aside basic firewood tools (chain and bow saws, hatchet, axe, maul, sledgehammer and wedges), the most important woodworking tool I possess is the drawknife. This enables one to quickly and efficiently peel bark off of saplings and poles (which alone increases their durability outdoors, and is essential to prepare them for other uses), and is also good for rough shaping work....more accurate than a hatchet, and quicker than a chisel in many cases. I probably use my drawknife about as often as any of the basic carpenter's tools like a crosscut saw or an electric drill.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.

I cannot think of a project that the orbital sander was not used. Whether painting, staining, or just applying a clear finish, you will want to sand to some level to smooth out the wood. Even when using barn-wood or reclaimed wood, I often at least sand the edges to get rid of sharp edges and revel some of the underlying fresh wood. I usually have about 4 or 5 different grit sandpaper on hand for my orbital sander, here is my favorite brand.


​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.

She came back to the mainland when her family was building a sky scraper in Denver. ( Well about as tall as any of the other down town high rises.) I got to tour it while it was being built.  Very cool !  So hanging around this crew of a family she picked up quite a lot.  The wife of her brother, the iron worker and pro chef, was an iron worker as well. The first lady ironworker I had ever met and I grew up around construction workers some what. Hard core people ( bound to rub off ).
We use a Dewalt 20V drill. It’s kind of embarrassing how much I love this drill.  I got so used to having a crappy one, that once I got a good one, I was hooked on it.  While you are getting the drill, don’t forget drill bits.  Don’t cheap out on those either.  Trust me.  You will use a drill on almost every project, so the investment is definitely worth it.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.

"Plaintiff never complained of discrimination to the on site owners. Moreover, Wirths invested a great deal of their personal time counseling Plaintiff to become a successful supervisor and Plaintiff never complained of difficulties with her direct supervisor even though Woodworker's Supply had and enforced (1) an antidiscrimination policy, and (2) a mandatory requirement to immediately report all incidents of discrimination."


about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.

I moved back to my small hometown just a few years later.  Had a stable income, now with my own home with a shop.  That’s were I started getting back into woodworking.  I have been doing it now on a steady basis for the last ten years or so.  I do it just for a hobby, but I enjoy doing it to pass the time or to try and make a new piece of furniture.
Thanks for the suggestion. At this point my plan is to focus on keeping things as they are. Many people have stated that they appreciate the current format. The videos are not necessarily intended for everyone, however they are for people that have a curiosity and a desire to learn woodworking. These are the people that will watch and raise questions and then ask the questions.

After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.


A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.

The first word that comes to mind for describing Jay’s work: Accessible. Even if you are brand-new to woodworking and don’t have many tools, you can follow many of Jay’s projects. It’s not just the choice of tools and techniques, but also his straightforward and friendly presentation style. Here is a video that’ll be handy for anyone just shopping for a new kitchen:

An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
The most common type of cedar used today is the Western Red variety. Western Red Cedar, as its name implies, has a reddish color to it. This type of wood is relatively soft, has a straight grain, and has wonderful aromatics. Western Red cedar is mostly used for outdoor projects such as furniture, decks, signs and exterior siding because it is naturally resistant to moisture and water corrosion. Cedar also makes for a great closet or chest for storing clothes and other fabrics because of its resistance to moisture. Cedar is moderately priced and can be stained to a variety of tones.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Jon Peters Art & Home is a show about DIY woodworking and other home-related topics. Jon keeps it interactive by encouraging viewers to send their project pictures to him so that he can have a look at them. And if you like some drama with your woodworking videos, Jon does occasionally record videos of him freaking out about things like cheap Chinese wood.

2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts. 

The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.

If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
Copyright © 2018 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
Arbortech Turbo Plane – The turbo plane is more than 7 times the cost of the Bad Blade Carver, however The turbo plane is kind of a more refined animal.  It probably isn’t fair to compare the two. The Turbo Plane leaves a better finish and can be used in a different way,  but for bulk removal and heavy shaping, I think the Bad Blade Carver wins. If you want the scalloped and smooth surface, then the Turbo Plane wins.
Staining wood is a process of darkening the overall tone by adding pigment, or dye, to it. Stains come in all shades and colors, ranging from light golden oak to rich, dark espresso tones. This is a beautiful way to achieve the exact tone that will work best in your home or business and is a very common way to finish wood. Stains are applied by hand in our workshop, giving a natural finish to the wood and maintaining the integrity of the wood-grain by controlling the amount of stain that is applied. Stains are utilized for both interior and exterior applications, although not all wood species take to stain uniformly and evenly so there are some drawbacks. For the most part, stain is very good choice in the finishing process.
As an x aerospace machinist I have run manual lathes and mills and programmed and run CNC as well. IMO a manual lathe is far more versatile and useful than a CNC for the average DIY buff. A CaN C is basically a very accurate production machine but to spend time programming, setting up, proving out just for a couple or several pieces is not practical ( unless you have money and time to spare)
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
×