2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.

Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.

About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.
One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
Check with Habitat for Humanity.  If they have a store you may find several good items such as a bench, bandsaw or etc.  When I retired and moved I donated  a complete shop full of woodworking power tools and hand tools to Habitat.  They sold them, I deducted them from my income tax.  Unfortunately I could not retire my desire to woodwork and at age 78 I built a shop and use only hand tools and a bandsaw.  Good exercise pushing  a LN #7.   Build yourself a solid bench with some southern pine with a moxon vise that can be built by hand.  Get some holddowns!

Rob Cosman and Paul Sellers. Rob is damn near a genius when it comes to woodworking. He routinely comes up with methods and tools that sort of change the way we all do things in the shop. The guy is also an amazing instructor. Paul Sellers is also an amazing instructor. These are the kinds of guys that all the rest on your list learned how to woodwork from!


While the router isn’t exactly necessary to build the most basic projects, it will really allow you to put that extra level of detail on a project so it isn’t quite so bland looking. Routers are also an extremely versatile tool that can be used in lieu of a jointer to get a straight edge on rough lumber, put a nice detail edge on a table top or piece of furniture, cut mortise and tenon joinery, cut dadoes and rabbets, mount in a table, or a countless number of other uses. Router bits can be pricey, so my advice would be to add bits as you need them for specific uses and projects. There are some variety pack kits available if you want a set to get started though. Also, there are smaller (trim) routers and full-size routers available. For the purpose of a beginner woodworking tool set, I recommend starting out with the small router and seeing just how much you can accomplish with that.
I’ve been seeing a lot of maker sites featuring both Osmo Polyx and Rubio Monocoat finishes (hardwax oils).  They seem to go nicely with the live edge tables that are so popular today.  I imagine these companies are doing a good job reaching out to the makers because it seems like an effective effort.  I’ve also seen some examples of Odie’s Oil and and it looks like a similar product only with less marketing flair.  I was on the fence and was leaning toward Rubio, only because it seemed like more makers were featuring it.   Then I ran across this series of 4 videos by Blacktail Studio that test out hardwax finishes each of 4 different ways.

My first projects were making things from pallet boards. I cut the boards to size using my jig saw.  It’s not quite as good as using a miter saw, but it got me by for a while with sufficient results.  Even now that I have a miter saw, I still use my jig saw A LOT to make notches (like for my outdoor table), or fun designs (like these deer heads last Christmas).
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.

Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  
Then there are the “practical” woodworkers that enjoy weekend projects and things that don’t require a ton of expensive tools, time, and expertise (HELLO, THAT’S ME).  I will be in the latter category.  Sure, you can invest in hand tools, but in the words of one of my favorite internet sensations, “ain’t nobody got time fo that.”  Let’s be practical here.
These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects  to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge.  Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
A long-established channel with Italian-American woodworking geek Marc Spagnoli and his sidekick Nicole.   It's filled with great tutorials, guides, reviews and generally high quality content.  I'd described as aimed at an improving, and committed, woodworker - he uses fairly lots of clamps and glue, and shows in professional how to build quality pieces, generally of furniture.  I learned a huge amount from here, and it's easy bedtime viewing.  
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
If you’d like to read some more about SketchUp, check out Ryan’s article on how to plan a home DIY project with SketchUp 3D Design for Daily Life: How to Plan a Home DIY Project With Sketchup 3D Design for Daily Life: How to Plan a Home DIY Project With Sketchup Doing a home improvement project on your own isn't always a simple matter. Sometimes it seems simple enough when you get started, but before you know it, you realize that if you had just taken... Read More . And if the idea of 3D design in general captivates your imagination, you should read our interview with world-class 3D artist Rafael Grassetti How A Dream Job Comes True: Interviewing World-Class 3D Artist Rafael Grassetti How A Dream Job Comes True: Interviewing World-Class 3D Artist Rafael Grassetti It's not every day that I get to pick the brain of a world-leading 3D artist -- but that's exactly what I got to do with Rafael Grassetti. You may not recognize Rafael's name, but... Read More .
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.

My name is Marc Spagnuolo and welcome to my channel. I am a podcaster, video producer, author, and woodworking enthusiast. I have contributed articles and video content to FineWoodworking.com, Popular Woodworking Magazine and WOOD Magazine. Producing the Wood Whisperer is a great way for me to combine four of my passions: woodworking, technology, education, and humor. I believe that even the most complicated woodworking project is just a series of steps. My goal with this channel is to show you the tools and techniques you need to perform those steps.
By the way, before you yell at me about the fact that the price on the links for the nail gun is more than $200, listen up I have a handy tip:  There are sales throughout the year on this exact package for $200.  That’s how I bought mine.  Just keep checking back.  And be sure to follow me on social media.  I keep checking it, too and if I see it’s on sale, I will post it to let you all know!
I Like to Make Stuff is the perfect channel for beginners who want comprehensive teaching on woodworking. It has a show called Maker 101 that goes into the basic skills you need to start making stuff. I Like to Make Stuff is not intimidating to the beginner because it isn’t afraid of showing woodworkers making mistakes on their project rather than always doing everything perfectly.
These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects  to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge.  Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
×