Swap meets and flea markets? Often you see people bring all the old tools out of their garage that grandpa handed down to them and that haven't seen any use for 40 years. Hand saws, chisels, planes, drills, and all other manner of hand tools that are hard to give away because most people can't even tell what they are. An old fashioned brace-and-bit falls into that category, and all the people want for it is a couple of bucks.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE
Well there it is, my top 5 list of the best beginner woodworking tools. Let me know your thoughts or some of your favorite tools for each category. Of course this isn’t an all-encompassing list, there are all of the little extras like tape measure, square, clamps, glue, etc. To see what I use for all of these options check out the complete list of tools from my shop.
Some DIY woodworking projects are too intimidating to even attempt because you don't think of yourself as a master woodworker. Backyard Woodworking dubs itself as the YouTube channel for the average guy. The channel takes you through simple projects you can do today, projects like a piggy bank, a birdhouse and a heart box—which is apparently the perfect gift for your sweetie!
I find, as others have noted, that braces are pretty easy to find, and bits for them in decent condition harder. I too tend to buy them whenever I see them. There are a number of varieties of brace, and some meaningful differences in them. Pay attention to the design of the chuck, and to whether the brace is ratcheting, or not. They're all good, but some differences in best application.
The directions that you'll find for making this Jack-o-lantern are found at HGTV, and they suggest using a battery operated votive to light up the lantern. I believe I'd try to figure out a way to add the "light" part of an inexpensive solar yard light instead. That way the jack-o-lantern would light as soon as it got dark. I wonder if that would work?
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
Install the roof rafters. Then, after the rafters are all set, install the purlins on top of the rafters as the roof supports. The metal roofing will be screwed onto these purlins later on. All purlins’ tails are cut into 9” length. The steel roofing will be hung 2” for the facia board supports. Then, after the roof frame is ready, install the roofing.
Then there are the “practical” woodworkers that enjoy weekend projects and things that don’t require a ton of expensive tools, time, and expertise (HELLO, THAT’S ME).  I will be in the latter category.  Sure, you can invest in hand tools, but in the words of one of my favorite internet sensations, “ain’t nobody got time fo that.”  Let’s be practical here.
Arbortech Turbo Plane – The turbo plane is more than 7 times the cost of the Bad Blade Carver, however The turbo plane is kind of a more refined animal.  It probably isn’t fair to compare the two. The Turbo Plane leaves a better finish and can be used in a different way,  but for bulk removal and heavy shaping, I think the Bad Blade Carver wins. If you want the scalloped and smooth surface, then the Turbo Plane wins.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
All in all, for whatever reason it is that you enjoy woodworking, then you always need to follow that passion.  There is always going to be obstacles to overcome, whether that be not enough money to buy your tools, or space to put those tools, or time to enjoy woodworking.  That is something that every person has to overcome.  Everybody has there own unique obstacles.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
By the way, before you yell at me about the fact that the price on the links for the nail gun is more than $200, listen up I have a handy tip:  There are sales throughout the year on this exact package for $200.  That’s how I bought mine.  Just keep checking back.  And be sure to follow me on social media.  I keep checking it, too and if I see it’s on sale, I will post it to let you all know!
Hope these top Woodworking YouTube Channels help you with all your future DIY woodworking projects! Make sure to use General's woodworking tools, like our best-selling Heavy Duty, All-In-One Aluminum Pocket Hole Jig Kit, 76 Piece Set With Carrying Case, or the 822 Digital Angle Finder Rule, 5-Inch. Use both tools and create a frame as your next DIY project!
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
×