Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
About Youtuber LAB11 Created designer furniture from scratch from wood and recycled materials like pallets or customizes and repairs existing furniture. The watchwords for our creations and customizations are: Pretty, durable and solid things. Here are the videos of some projects creations but also of layout of the workshop, A video per month out at least.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Only comment would be to start with manual machines -once you have them mastered, then worry about CNC. I'm only 71 at this point, but I still have a lot of things left to master! Try to find even a HF mini-lathe and mill used, and get started. The sooner you start, the sooner you become experienced, Just a warning though - machining is just as addictive as wood working.
Hey Great Article,Thanks. 4 months ago, I started looking for woodworking.The industry is extremely interesting,but I have problems with how I can do it.My uncle who has been doing more than me in this industry,has suggested to me to follow Teds plans.Do you think it’s a good move to follow these plans??I keep reading good reviews about Teds plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
About Youtuber Steve Johnson is a full time life-long hobbyist woodworker committed to helping new and experienced woodworkers achieve the "shop of their dreams" - even if (especially if?) they don't have a dream budget to work withHis videos can be seen at "DownToEarthWoodworks" on YouTube and his articles appear monthly in Highland Woodworking's on line newsletter "Wood News Online.".
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
If you'd like to learn more about the differences between hardwood species, I can think of no better resource than R. Bruce Hoadley's 1980 masterpiece, Understanding Wood: A Craftsman's Guide to Wood Technology. Not only does Hoadley detail nearly every species used for woodworking, he does an exceptional job at describing how to prepare, work with and finish these hardwoods. This is an industry-standard resource, one that I'd highly recommend to every woodworker.