If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws. Because of this, I'd stick to the two saws we looked at in the $500 build: The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110. These two additions bring our running total to just over $500.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
The problems that we least expect. Five years ago i purchased a bicycle and discovered while riding that I had developed balance problems. I ignored the problem and stopped riding the bicycle.During this period I built a workshop in my basement and stocked with the best handtools. My lifelong dream was to be an anarchist! In February 2012 I started having episodes of more severe balance problems which resulted in hospitalization and extended nursing home rehabilitationl for six months. The diagnoses is Parkinson Disease which causes muscles to react to unwanted brain signals. Needless to say the therapist ordered "no woodworking" period" because of the hazards associated with machines and sharp tools. I presented my case that I did only handwork with hand tools. The therapist answer was "NO!". Now I'm confined to using a walker or wheel chair and reading how you all are enjoying the smell of sawdust.
About Youtuber The English Woodworker Blog aims to share with you our passion for traditional woodworking and keep you up to date with the goings on in and around our workshop. We are the owners of ’Maguire Workbenches’ and spend much of our time designing and building high quality workbenches so no doubt there will always be a lot of workbench talk.
Hey Great Article,Thanks. 4 months ago, I started looking for woodworking.The industry is extremely interesting,but I have problems with how I can do it.My uncle who has been doing more than me in this industry,has suggested to me to follow Teds plans.Do you think it’s a good move to follow these plans??I keep reading good reviews about Teds plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.
About Youtuber This channel is created to share my passion for woodworking and guide beginners into realizing the joy of this hobby. Woodworking is fun, inspiring and helps you to design, create and relax. You can pick up a piece of wood and create something out of it and the result is uplifting. You just created something valuable from piece of wood.
How about a hunk of butcher block counter top on a 4X4 (legs) base on locking wheels. Round over the good side and it is a rolling kitchen stand - chopping block - island. Flip the top over, lock the wheels, and it's a bench. There is a vise that is sold by Woodcraft that drops onto a mounted post in both vert and horiz positions that would be perfect for a small flip top bench. The post would be mounted to the underside, unseen till the top was flipped and the vise dropped on. It pivots but when the jaws are clamped it is tight.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
Right now you're thinking, "but the plans say to use a table saw for this." That's OK , because the great thing about a circular saw is you can turn it into a table saw. There are plenty of videos online showing how to do this, but you are essentially cutting a slot in a piece of plywood, mounting the circular saw to it, and flipping it over. With careful planning you can have a good basic table saw without spending hundreds of dollars, and it can come apart if you need to save space. With that setup you can cut long pieces of wood that you may not be able to brace properly to cut with the circular saw. You can also make more accurate cuts than by holding the circular saw. It can also be used to cut simple dados and to cut a bevel. You do need to be careful, as it won't have the blade guard covering the saw blade anymore.
As far as sharp goes, I subscribe to the school of thought that you need to hone an edge to hold up to what is is going to be cutting. The more you hone an edge, the thinner it becomes. This makes it sharp, but it also erodes it’s physical strength. If you want to slice paper or shave the hairs off your arm, go happy with a 2000 grit polish. If you are going to be hogging through wood, that edge will round over very quickly. IMHO you are better with a 500 grit finish at the most, and usually I am totally happy with the result of the 360 diamond hone.
If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.
The variety of colors and tones, textures, and grain patterns seen in most hardwoods create some of the most beautiful and unique furniture in the world. Hardwoods are generally more expensive than softwoods, but the finished look can be well worth the additional cost. Hardwoods are often more durable and are therefore generally recommended for tabletops and countertops. Many hardwoods do not need to be stained, but rather hand-finished with natural oils to enhance their beautiful grain and texture.
Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
Let's talk about a few strategies for building out your shop below retail price. There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss. First of all, not everyone lives in an area where these avenues exist. Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand. Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Rob Cosman and Paul Sellers. Rob is damn near a genius when it comes to woodworking. He routinely comes up with methods and tools that sort of change the way we all do things in the shop. The guy is also an amazing instructor. Paul Sellers is also an amazing instructor. These are the kinds of guys that all the rest on your list learned how to woodwork from!
One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
This post speaks right to the heart of frugal woodworking. The woodworker addresses how to make a dye from tea and alcohol that is fast drying and will not raise the grain of your wood. Technically I guess it is both a stain and a dye since since the tannins in the tea will actually change the color of the wood, and the other colors in the tea act more like a stain. Either way it is a great idea.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.
I Like to Make Stuff is the perfect channel for beginners who want comprehensive teaching on woodworking. It has a show called Maker 101 that goes into the basic skills you need to start making stuff. I Like to Make Stuff is not intimidating to the beginner because it isnâ€™t afraid of showing woodworkers making mistakes on their project rather than always doing everything perfectly.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.