If you had bothered to watch the video this would have been explained. The cupping you see is a result of mass manufacture. Few tool makers will take the time to lap the back of a chisel to degree a craftsman will (much less the bargain brand he’s using). It’s simply not practical for them to do so and still make their price point. Some higher end (Lee Nielsen, Lee Vally, Veritas) chisels will be closer but even these will require some degree of hand honing/lapping. Using a flat stone, with at most couple hours of practice, you will reliably create razor sharp straight edges.

The Jay's Customs Creations YouTube channel releases weekly videos on shop projects and dimensional lumber projects. Jay's show can really help you if you want to do DIY woodworking projects on a budget. He sometimes shows viewers how to complete the project without electricity and using only hand tools. He goes over the prices he paid for materials to give people a realistic budget for the project before they get started.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.


Build projects from wood the fast, strong, easy way using pocket-hole joinery and the Kreg Jig® R3. With the Kreg Jig, all you have to do is drill a hole in one of the pieces you want to join. Then drive in a Kreg Screw. The self-tapping tip draws the joint together and holds it tight, so you can create beautiful, durable projects quickly. The portable Kreg Jig R3 features two hardened-steel drill guides, built-in guides that make it easy to set up on a wide range of material thicknesses, and a clamp pad—all in a compact carrying case.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
Although we focus primarily on the use of wood in our work, CZ Woodworking also incorporates materials other than solid wood into our workshop. We work with metalworkers, glass companies, designers and artisans alike to bring various materials together to create custom pieces. Examples of additional materials we use are wrought iron, steel, glass, stone and more. By combining various mediums together, we are able to achieve the specific look that fits your needs best. Please contact us directly to inquire further.
Use the square and position the pivot point onto the board top and slide the square up to the 5 on the line up “COMMON TOP CUT” outside the board. Mark the line as for the angle. After first angle is cut, measure the rafter length from the tip cut to get the seat cut measurement. Mark the seat cut and place the pivot point onto this mark and do the same step to get 5/12 angle. From that angle, measure up 2 ½” and make the line.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
I ONLY use water as a lubricant on all my stones. When they get clogged I take a nail brush and hand dish detergent to them to clean them. When a carborundum stone gets worn I do figure 8s on a flat piece of concrete with lots of water to reflatten it. I don’t like oil because it gums up over time and is then harder to clean. I keep a carborundum and a Quachita stone by the kitchen sink for knives. I probably haven’t used the carborundum stone in several years. I scrub the Quachita stone at roughly 18-24 month intervals. It’s white, so it’s easy to see the steel accumulating. I can feel a noticeable difference after scrubbing the stone. This has been my standard practice for almost 50 years, so I’m not inclined to change it.

Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
×