A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.


This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.

Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
About Youtuber This channel is created to share my passion for woodworking and guide beginners into realizing the joy of this hobby. Woodworking is fun, inspiring and helps you to design, create and relax. You can pick up a piece of wood and create something out of it and the result is uplifting. You just created something valuable from piece of wood.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration. 

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post. 

One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too. 

I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
*any* glass made by the float glass process will have the same level of flatness (>95% of today’s colorless glass). However, thicker is better and I would see 5mm as the absolute minimum. When glass slabs get bigger/heavier their shards pose a real risk in case they crack. Therefore, 5 or 8mm tempered glass is what you should be looking for. If you can’t find tempered glass, cover the back with UV-stabilized (all weather) tape: this will hold the shards together and you don’t get any exposed edges.
In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.
Woodworking is a highly visual craft. There’s just something photogenic about lumber getting cut to size, dry-fit, glued or tacked together, and finally sanded down and finished into a beautiful piece of furniture. Even if you’re not a woodworker yourself, watching high-quality woodworking videos is a great way to learn about how stuff gets made, and who knows, you might even realize you want to make something yourself.
About Youtuber Architecture at a small scale expressed through woodworking and film making. My videos here are for entertainment, to share what I do, and to maybe provide some inspiration. Woodworking can be dangerous if all safety precautions are not taken. You can have a safe, enjoyable, and even inspirational time in your shop by understanding your own tools, materials, and your own skill level.
Another staple in the beginner woodworkers tool kit has to be the cordless drill. Used for either drilling holes or driving fasteners, this tool gets used on almost every project. There a tons of options here regarding size of batteries, aka power, but something around the 18-20 volt range is a good all-around size that will not leave you constantly wishing you had something larger or smaller. Here is a large accessory kit at a good price that should give you most of the drivers a bits you will need.

Teak is an excellent choice, the “crème de la crème”, for fine outdoor furniture. Teak is highly weather-resistant by nature, which means that it does not have to be weatherproofed when used outdoors – although it often is finished and stained for aesthetic purposes. Teak is one of the most expensive exotic hardwoods there are, but it will look absolutely beautiful and maintain its integrity over time.


The majority of books I read are lost to my memory since I had originally read them in high school when I was very active in scouting. I fell out of focus and didn't really get interested again in woodworking specifically until the last few years as my desire for learning self-sufficient skills has grown beyond just survivalism. I've read the first five Foxfire books and paid great attention to the various non-electric projects and old fashioned woodworking skills. I have also begun to watch episodes of the Woodwright's Shop (my father used to watch it heavily, but at the time I paid very little attention) and wish the first season was online since he does a lot of the basics in that first season. Most of my other reading has been online or watching videos such as the construction of a woodworking bench and the like. I do get smanterings from other books such as the Back to Basics by Abigail Gehring.
×