Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you. 

We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap.  ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15).  1 rip handsaw (used ones can be found at Antique stores for $20 or less.  Try to find one that is fairly sharp to start with).  Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both).  A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.
There are and they are considerably cheaper. I found a pair of glue brushes on Amazon for less than half the price of a singles dedicated glue brush. I tested them out on a recent gluing and they work well for spreading glue and getting it into dovetails and mortises. When you are done you can either run the brush underwater to clean it or wait until the glue dries the pluck it off the bristles with a few easy pulls. The glue comes right off the silicone bristles.
Frank is an architect/woodworker who creates videos with stunning visuals that are intended to inspire you. Frank uses his top-notch filmmaking skills to fast-forward himself as he works on a project. He even uses stop motion—an animation technique that enables him to manipulate objects (such as chisels and clamps and block planes) to make it appear they are moving on their own.
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.
What tools are needed to start woodworking? Well, this list can vary greatly depending on your budget. The best beginner woodworking tools are subjective but can vary largely depending on how much money you are willing or able to invest to start out in woodworking. It can also vary depending on if you are wanting to start out woodworking just as a hobby or as a side-hustle business. Most of the best beginner woodworking tools on this list are either tools I own, have owned, or at least have used in the past.
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
These how to videos and articles of information are dedicated to my woodworking instructor who trained me during my apprenticeship. This body of work is also in honor of the journeyman who were generous in sharing their woodworking knowledge and skills with me throughout my long career. All of you have helped me to make a wonderful living  in a great craft. My hat is off to all of you.
The next thing to look at was how to order the list. Probably the most obvious was subscriber count (which is how it is ordered), video count was also a possibility. One thing I was looking at, was the subscribers to video ratio. For example the Channel Inspire To Make has 101,000 subscribers, but when you realize that they only have 20 videos, the subscriber to video ratio is very impressive. I really do recommend you check it out as the videos really are very well made.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.

The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
×