While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
The trick is to use sandpaper. It’s a good quality abrasive material and is readily available. You’ll want a selection of different grits – low grits to get started, higher grits when finishing. The reason this is cheaper is that you can get a selection of 5-10 different sandpapers for under $20. Getting even a couple of decent sharpening stones wouldn’t be possible at that price. In the long run, they’ll last longer but this is a budget option we’re talking about.
Another example is lathe tooling or metal gravers which are routinely polished on fine agate stones and these don’t chip or roll an edge unless abused. These are one of the times where a jig is a requirement for reproducible results and a couple degrees off the recommended angle can make a difference. For a wood work, a couple degrees either way won’t really be noticed.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
About Youtuber This channel features work done by Marsh Wildman of Wildman Technology & Fabrication. I'm a maker/artisan/technologist specializing in bringing the dreams of others to reality. If you can convey your concept to me, I can build it for you! We reclaim and upcycle when possible. Wood working projects. Plasma cutting and welding. Machine shop services, PROTOTYPING and setting up production lines.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
Steve Ramsey. He's an energetic, fast-talking eccentric whose built his channel based on projects that can be done without investing in fancy tools. He trudges out a banged-up table saw from his garage, chops stuff up on the bed of his truck, and generally produces well-structured projects - even if I can't agree with his design aesthetic and color choices. Lots of good stuff to learn and a great channel for someone starting out.
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt. Unfortunately, that ended up with the guy we hired stealing from us…..uggggh. When will we ever learn to not be so trusting?! Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!! Sad. Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.
Frank Howarth is a unique guy - educated as an architect, but with practical woodworking skills to rival any journeyman. He has the most enviable workshop of anybody I've seen, and his projects are aspirational on every level - creativity, originality, ingenuity, and craftsmanship. He devotes a lot of time to talking about the layout and design of his ever-changing workshop, and there's a lot of clever ideas to steal and pass off as your own. If you can't tell, I love Frank. Oh, and his stopmotion videos are awesome.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.
The Jay's Customs Creations YouTube channel releases weekly videos on shop projects and dimensional lumber projects. Jay's show can really help you if you want to do DIY woodworking projects on a budget. He sometimes shows viewers how to complete the project without electricity and using only hand tools. He goes over the prices he paid for materials to give people a realistic budget for the project before they get started.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Do you enjoy woodworking? Do you have a budget that you have set aside just for your woodworking? If you are not a millionaire, than more than likely you will have some sort of a budget. Let me give you a little insight into why you are here and what you will find on this site. Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job? Or maybe you are wanting to turn your hobby into a full time job. If that sounds like you than your in the right place.
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
As far as advice goes, I'm like a lot of the other folks on this thread; make a shop budget that fits into your existing budget and stick to it. Whenever you can foresee a larger expense, skrimp and save, cut costs in other areas of non-essential spending, and accept that sometimes, you NEED to go outside of your budget. In my experience, if it means enough to you, you can make it work. Good luck!
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.