The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops. 

Check with Habitat for Humanity.  If they have a store you may find several good items such as a bench, bandsaw or etc.  When I retired and moved I donated  a complete shop full of woodworking power tools and hand tools to Habitat.  They sold them, I deducted them from my income tax.  Unfortunately I could not retire my desire to woodwork and at age 78 I built a shop and use only hand tools and a bandsaw.  Good exercise pushing  a LN #7.   Build yourself a solid bench with some southern pine with a moxon vise that can be built by hand.  Get some holddowns!
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
I, too, would pass on the Jawhorse, and agree with the suggestion of a solid bench. (Remember, it can double as a desk if space is limited.)  A used solid-core door can be a starting point, but there are better options, such as laminating your own from scrounged 2x4s. Spending time at flea markets looking for old tools that can be reconditioned is a good suggestion, too.
Check with Habitat for Humanity.  If they have a store you may find several good items such as a bench, bandsaw or etc.  When I retired and moved I donated  a complete shop full of woodworking power tools and hand tools to Habitat.  They sold them, I deducted them from my income tax.  Unfortunately I could not retire my desire to woodwork and at age 78 I built a shop and use only hand tools and a bandsaw.  Good exercise pushing  a LN #7.   Build yourself a solid bench with some southern pine with a moxon vise that can be built by hand.  Get some holddowns!
Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house.  If you don’t have one, they are a few bucks each and WELL worth the investment.  AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂
I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flat­tening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelo­gram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall

Not only is having a full time job is hard to do woodworking, if you have a family as well, then that is another thing that you are going to have to juggle as well.  For me its a no brainer.  I always choose my family over my hobby of woodworking.  But when my family or job does not need my presence, that’s when I am free to let my brain just run loose on new ideas of what to build next.

One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
Before I give you my list, I am assuming (and yes, I know what assuming does) that you already have a tape measure, screwdriver and a hammer. These are common household items that most people (woodworkers or not) keep around the house.  If you don’t have one, they are a few bucks each and WELL worth the investment.  AND they are my favorite types of stocking stuffers—even if it is just July, it’s already on my mind 🙂
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.

If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them! 

The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Available in both water-based and oil-based finished, polyurethane is one of the most common practices used in woodworking today. Polyurethane can be sprayed, brushed or rubbed onto the piece to obtain either a satin, semi-gloss or glossy finishes. Polyurethane is a very versatile finish that will last for many years and is easy to clean and maintain. 

A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Many home improvement projects and custom woodworking pieces alike call for a painted finish. Depending on the application process, paint can create either a rustic or refined finish, and it looks great when both paint and stain (or oil) are combined together in a piece (we love the look of a painted table base with a stained or oil-rubbed table top. See our portfolio for some great examples of this style). Paints are great for both exterior and interior protection and are available in an almost infinite number of color tones. Finishes include flat, eggshell, semi-gloss, and high-gloss depending on the amount of sheen you desire.
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.

A personal favorite of Chris’s, this wood is the ideal choice for woodworking pieces that want to showcase beautiful grain and an excellent finish. The naturally wavy grain of Black Walnut creates a look that is artistic and abstract, with a density that also gives weight and strength to the piece. Black Walnut stains wonderfully, but is almost best when the natural elements are emphasized with an oil finish only – and it should never, ever, be painted!
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses. 

Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
I have a stable income like a said earlier, but when it comes to having extra cash to just blow on a hobby, well I was never always that fortunate.  So when I wanted a new tool or even to just purchase lumber, I would have to save up until I could purchase it.  I know that sounds like most people, but it has taken me several years to just even get the basic tools of woodworking.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
Fine Woodworking Tools and Supplies at Highland Woodworking – make us your woodworking tool supply source. Woodworking Hand Tools are one of our passions at Highland Woodworking so we sell the very best hand tool brands in production today. Handmade, high quality hand tool lines such as Auriou Rasps, Barr Forged Tools, Gransfors Axes, Lie Nielsen Tool Works, Woodpeckers Precision Tools and numerous other fine hand tool makers. We love fine Woodworking Power Tools too, so we sell Festool Power Tools and SawStop - the best power tool brands for woodworking. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools, equipment & supplies.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
I have been around woodworking my entire life.  I have always been intrigued by how you can take something like lumber and turn it into a wonderful, beautiful piece of furniture.  Once I graduated high school, I kind of got out of woodworking.  I wanted to go a different route.  I was going to college and just trying to make ends meet on the bills.
About Youtuber This channel features work done by Marsh Wildman of Wildman Technology & Fabrication. I'm a maker/artisan/technologist specializing in bringing the dreams of others to reality. If you can convey your concept to me, I can build it for you! We reclaim and upcycle when possible. Wood working projects. Plasma cutting and welding. Machine shop services, PROTOTYPING and setting up production lines.
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.
The majority of books I read are lost to my memory since I had originally read them in high school when I was very active in scouting. I fell out of focus and didn't really get interested again in woodworking specifically until the last few years as my desire for learning self-sufficient skills has grown beyond just survivalism. I've read the first five Foxfire books and paid great attention to the various non-electric projects and old fashioned woodworking skills. I have also begun to watch episodes of the Woodwright's Shop (my father used to watch it heavily, but at the time I paid very little attention) and wish the first season was online since he does a lot of the basics in that first season. Most of my other reading has been online or watching videos such as the construction of a woodworking bench and the like. I do get smanterings from other books such as the Back to Basics by Abigail Gehring.
That just reminded me of a FWW piece many years ago that had me rolling on the floor.  Craftsman had built a large piece being delivered to an apartment on the top floor.  Couldn't get it on the elevator so they got controll of the elevator and ran the top of it to be even with the floor, loaded the piece on the top of the car and rode with it inside the shaft while balancing it and keeping it from hitting the shaft walls.  At some point in the trip up they lost control of the elevator and it started making trips up and down to other floors.  I'll see if I can find it.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
A personal favorite of Chris’s, this wood is the ideal choice for woodworking pieces that want to showcase beautiful grain and an excellent finish. The naturally wavy grain of Black Walnut creates a look that is artistic and abstract, with a density that also gives weight and strength to the piece. Black Walnut stains wonderfully, but is almost best when the natural elements are emphasized with an oil finish only – and it should never, ever, be painted!

Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects. 

Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.
Only comment would be to start with manual machines -once you have them mastered, then worry about CNC. I'm only 71 at this point, but I still have a lot of things left to master! Try to find even a HF mini-lathe and mill used, and get started. The sooner you start, the sooner you become experienced, Just a warning though - machining is just as addictive as wood working.

I taught (teach) several aspects of "green woodworking" and related subjects, so I love your question. The buying and using of old tools is great...no matter the source. However, I have seen much frustration ensue over getting them adjusted, and "work ready." As often a beginner with limited budgets, also have limited traditional skill sets as well in understanding these tools and sharpening them. You must be patient with yourself, as tuning these old tools up will be very time consuming. Sharpening (and the proper tools of sharpening) should be your first acquisition. So many folks buy chickens before building a proper "chicken coop." Traditional tools are the same way, as there is no reason to own them, if you can't keep them properly honed.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.

Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.

For under $20 I am very impressed with the Bad Blade Carver by Kwik Tool.  Mounted in a 4.5″ grinder, it removes a ton of material quickly yet allows a fair amount of control.  The disk has only 6 teeth so the carver is mainly a solid disk with very few teeth to bite and create kick-back or dig-in. I found I had the best control when engaging the blade between 12 o’clock (top of the grinder) and 3 o’clock. When in that range it was not overly aggressive and left me in control.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
Find a wide selection of edge banding tools and hand tools like chisels and files.  Find other woodworking products like protective gear, clamps, and wood finish.  Whatever your project, find the quality woodworker's supplies you need to complete the job.  Shop over 18,000 products from the top names in the industry today.  Shop our hardware online, or order from our catalog, available to you free of charge.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.

About Youtuber My name is Andrei. I live in Russia and run my small business. Woodworking is my passion. I am the only woodworker in the shop. It is my full time job. I make only end grain cutting boards. I've been making end grain cutting boards for years. Sometimes I make end grain chessboards, end grain jewelry boxes, etc. Also I prepare woodworking plans.
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
×