These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps. 

Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
Another option is to use two small clamps to hold two boards in place, and then wedge the wood pieces, that you’re trying to glue, in between them. I’ve found that this works better than the ratchet straps when trying to glue up thinner lumber, like boards from old pallets. When using this method, you should have the wood on a completely flat surface, and often it helps to put some weight on top to keep it from bowing.

In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.


To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
You’ll find here, quite a comprehensive list of YouTube woodworking channels, and I must thank the woodworkers of reddit for helping me put this list together. I did originally decide decide that a channel needed to have a minimum of 1000 subscribers to be included on the list but after a lot of feedback I decided to include every channel that was sent to me (as long as it was woodworking themed). There were a couple of channels (Clickspring and Inspire to Make) that were on the list that I have removed because they weren’t strictly woodworking, but still do think that they are definitely worth checking out.
She came back to the mainland when her family was building a sky scraper in Denver. ( Well about as tall as any of the other down town high rises.) I got to tour it while it was being built.  Very cool !  So hanging around this crew of a family she picked up quite a lot.  The wife of her brother, the iron worker and pro chef, was an iron worker as well. The first lady ironworker I had ever met and I grew up around construction workers some what. Hard core people ( bound to rub off ).
​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  
In the second part of our I Can Do That Workbench series, we build the torsion box top. It features a replaceable hardboard top surface and an affordable quick-action face vice. The bench’s design also allows for storage on both sides of the center beam and for good measure, we’ve added flip down casters and made sure we had clamp storage and power access.
The Japanese style saw or Japan saw, depending on who you ask, can easily replace both the push saw and the dovetail pull saw for most of your needs. This is why I included the Japanese style saw in my woodworking budget starter kit. If I was starting over, and just going to buy one saw, this would be the one. I purchased an Irwin, but there are several other brands out there. I just found this one to be the best value at the time I was shopping.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.

The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
About Youtuber Jon Peters Art & Home teaches and inspires you to make art, woodworking, and home improvement projects at home. Whether you're a beginning artist, a practical do-it-yourselfer, or a professional craftsman, my videos will provide a how-to guide to great projects.I will show you the tools, plans, and tricks of the trade to bring art and design to your home.

A long-established channel with Italian-American woodworking geek Marc Spagnoli and his sidekick Nicole.   It's filled with great tutorials, guides, reviews and generally high quality content.  I'd described as aimed at an improving, and committed, woodworker - he uses fairly lots of clamps and glue, and shows in professional how to build quality pieces, generally of furniture.  I learned a huge amount from here, and it's easy bedtime viewing.  


To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
About Youtuber I do woodworking projects, pallet projects, tool reviews, DIY projects and quick tips. A goal of mine (As a woodworker) is to build custom/ fine furniture. I also want to help & inspire others. The woodworking/DIY community is great!. I've learned quite a bit from other woodworkers and hope that others will learn from me too or at least get inspired to build something.
The type of wood you choose will determine the overall strength, look and cost of the finished piece. Many varieties of wood exist, and CZ Woodworking will work with each customer to determine what wood will fit your needs best. Each wood has its benefits and can be utilized in a number of different ways to create various looks within a project. Explore the various samples below to determine what might work best for you.
Copyright © 2018 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.

The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.

Not only is having a full time job is hard to do woodworking, if you have a family as well, then that is another thing that you are going to have to juggle as well.  For me its a no brainer.  I always choose my family over my hobby of woodworking.  But when my family or job does not need my presence, that’s when I am free to let my brain just run loose on new ideas of what to build next.

Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.

Steve Ramsey makes woodworking fun. His YouTube Channel, Woodworking For Mere Mortals Building, shows Steve making cool stuff in his garage in Marin County, California. From games and toys to special holiday projects during his 12 days of "Craftmas" (wooden snowflakes!), Steve consistently puts out new DIY woodworking videos and projects every Friday.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
The next thing to look at was how to order the list. Probably the most obvious was subscriber count (which is how it is ordered), video count was also a possibility. One thing I was looking at, was the subscribers to video ratio. For example the Channel Inspire To Make has 101,000 subscribers, but when you realize that they only have 20 videos, the subscriber to video ratio is very impressive. I really do recommend you check it out as the videos really are very well made.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
This is known as the “Scary Sharp” method and I first learned of it on Usenet back in the day. I’ve had pretty good luck only going up to 2000 grit automotive paper. That stuff is commonly available near the spraypaint at Wally-world. At this grit, I can easily shave the hair on my forearm. For a plate, I use a single 12×12 tile from a Big Box store. 

If you choose paint for your finish, you won't want to waste your money on woods known for their color and beauty when stained, so avoid richly-colored species such as oak, maple, walnut or mahogany. For painted projects, poplar is a very good choice because it is relatively stable and takes paint quite well (not to mention that it doesn't look all that good stained).
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.

Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.


I just do it. Lol. Most of my projects are for my wife so its easier to scrape money together then listen to complaints about them not getting done! Seriously though, its tough. I have two expensive hobbies......woodworking and bass fishing, latter of the two being the worst. I reserve all my side work money for the two. One thing that helps is owning our own saw mill, lumber is basically free other then time.
There are and they are considerably cheaper. I found a pair of glue brushes on Amazon for less than half the price of a singles dedicated glue brush. I tested them out on a recent gluing and they work well for spreading glue and getting it into dovetails and mortises. When you are done you can either run the brush underwater to clean it or wait until the glue dries the pluck it off the bristles with a few easy pulls. The glue comes right off the silicone bristles.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.

We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.


What better way to continue our #2x4andMore week on the 4th of July than with 4x4s! 4×4 wood posts are good for more than just fences and beams. We’ve rounded up 15 of our favorite 4×4 wood crafts to inspire your DIY creativity. You can buy brand new 4×4 posts at your local hardware store or find 4×4 scrap wood. Either way you’ll only need to a few more materials to make your 4×4 wood crafts into a reality.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key stor­age, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs. 
Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
I find, as others have noted, that braces are pretty easy to find, and bits for them in decent condition harder. I too tend to buy them whenever I see them. There are a number of varieties of brace, and some meaningful differences in them. Pay attention to the design of the chuck, and to whether the brace is ratcheting, or not. They're all good, but some differences in best application.
"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
Copyright © 2018 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
Clamps are absolutely essential for most woodworking projects. This is why I’ve included clamps in the list of tools that beginners need when starting woodworking on a budget. However, I often run into situations where I don’t have enough or the right kinds of clamps. Today I’m going to share a few ways that I’ve gotten by without just going out and buying more clamps.
Check with Habitat for Humanity.  If they have a store you may find several good items such as a bench, bandsaw or etc.  When I retired and moved I donated  a complete shop full of woodworking power tools and hand tools to Habitat.  They sold them, I deducted them from my income tax.  Unfortunately I could not retire my desire to woodwork and at age 78 I built a shop and use only hand tools and a bandsaw.  Good exercise pushing  a LN #7.   Build yourself a solid bench with some southern pine with a moxon vise that can be built by hand.  Get some holddowns!
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
Pocket holes may get a bad rap from “fine” woodworkers, but they are the most accessible and versatile form of joinery for any woodworker. You will find tons of pocket holes in the highest end custom cabinetry kitchens, so I don’t hesitate to use them when needed. They are great for quick DIY furniture projects like my pub table here. I actually own bow the low and medium budget options below because they both have their place in my shop and I can choose which to use depending on the application. If you’re not sure what size pocket hole screws you will need to start out with, here is the variety pack that I first purchased.

Clamps are absolutely essential for most woodworking projects. This is why I’ve included clamps in the list of tools that beginners need when starting woodworking on a budget. However, I often run into situations where I don’t have enough or the right kinds of clamps. Today I’m going to share a few ways that I’ve gotten by without just going out and buying more clamps.


That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.

I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​ 

We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
The trick is to use sandpaper. It’s a good quality abrasive material and is readily available. You’ll want a selection of different grits – low grits to get started, higher grits when finishing. The reason this is cheaper is that you can get a selection of 5-10 different sandpapers for under $20. Getting even a couple of decent sharpening stones wouldn’t be possible at that price. In the long run, they’ll last longer but this is a budget option we’re talking about.

Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
×