This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects  to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge.  Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
Paul Sellers’ videos cover a wide variety of woodworking topics. He has an active channel on YouTube where his most popular videos are on making a mortise and tenon joint and making a dovetail joint. He is also the presenter at Woodworking Masterclasses where he teaches members to make furniture using a minimum of tools and equipment. The list below is Paul’s latest videos on YouTube. We hope you will find them informative and helpful.
Often referred to as Douglas Fir, this softwood has a rather straight, pronounced grain that has a reddish brown tint to it and is moderately strong and hard for a softwood. Fir is most often used for construction building materials, however it’s inexpensive and can be used for certain aspects of furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain uniformly, so it’s best when used in projects that require a painted finish.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber.
Tung oil is derived from the nuts of trees that are native to Asia but have been cultivated in other parts of the world. This is a durable finish that has a rather quick drying time and is very moisture resistant. Tung oil penetrates the woods surface, soaking deep into the wood grain for a fine finish. Tung oil is great for exterior furniture, tabletops and countertops.
Ash is a white to pale brown wood with a straight grain. It’s pretty easy to work with, is a fairly hard and dense wood, and takes to stain quite nicely. Ash has a medium to coarse texture similar to oak. The grain is almost always straight and regular, though sometimes moderately curly or figured boards can be found. Ash is becoming harder and harder to find, so it ranks as an increasingly expensive material to use.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.