Another staple in the beginner woodworkers tool kit has to be the cordless drill. Used for either drilling holes or driving fasteners, this tool gets used on almost every project. There a tons of options here regarding size of batteries, aka power, but something around the 18-20 volt range is a good all-around size that will not leave you constantly wishing you had something larger or smaller. Here is a large accessory kit at a good price that should give you most of the drivers a bits you will need.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​ 

About Youtuber Architecture at a small scale expressed through woodworking and film making. My videos here are for entertainment, to share what I do, and to maybe provide some inspiration. Woodworking can be dangerous if all safety precautions are not taken. You can have a safe, enjoyable, and even inspirational time in your shop by understanding your own tools, materials, and your own skill level.

Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
All you need to get an edge on your hand tools and pocket knives is a 100/300 grit combo stone from your local hardware, even horrible fright. This shouldn't cost more than $10. Then go to the natural slate section of the home center or flooring store & find 3-4" natural slate tile that you can barely see the grains in. This should cost another $1 or so. This tile is roughly 800 grit. If you can't find natural tile in your area, you should be able to find an 'Arkansas' stone for <$5. If you can scare up some Chrome Oxide and a piece of leather (piece of cardboard or block of MDF also work) all the better. These three things will cost you $15 and get your edged tools sharp enough to take hair off your arm and chips of your lumber. 

We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.

The last tool I recommend for every beginning woodworker is a quality router. While many routers available today offer two different bases (a stationary base and a plunge router base), for most beginners, a quality stationary base model will take care of quite a number of tasks, and can also be mounted in a router table should you choose to invest in (or even build one) one down the line. Choose a router model that is at least 2-HP and has electronic variable speed controls (as larger cutting bits should use slower speeds), a soft start mechanism and is easy to make bit changes (preferably with the ability to use both 1/2-inch and 1/4-inch shank router bits).
Mitre Block/Box for Cutting Coving Skirting Boards Polypropylene mitre box for accurate cutting of mitres and butt joints. Colours may vary from image shown. Stock No: 633731 EAN: 5055058172877 External Size: LxWxD = 300x140x75mm Internal Size : LxWxD = 300x105x58mm Colour: May Vary: Image is for illustration purposes only. Manufacturer: Silverline.
The second big tool you need is a saw. There are many types of saws, and this can be the trickiest part of setting up a shop on a budget. As a beginner, you'll likely be using woodworking books, magazines and websites for instruction and inspiration. Unfortunately, most of these sources consider a table saw a beginner tool. For those of us on a budget, or with little space, a table saw may not be an option. They cost several hundred dollars to start, and take up several square feet of floor space. Instead, look for a good circular saw that allows you to adjust the depth and angle of cut. It's also nice to have a laser to help guide the cuts. You can get a decent circular saw for around $100.
Oak is one of the most widely used and respected hardwoods in furniture making. Available in two varieties — red and white — oak is very strong and also quite heavy. White oak is sometimes preferred for furniture making because it has a slightly more attractive figure than red oak, but either variety can give you a beautiful finish that stains very well. Oak can be used for almost any woodworking purpose, and is an excellent choice for pieces that will last a lifetime – literally! As they say, it is “solid as oak”!
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
×