By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ... More + Product Details Close
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
About Youtuber Chop With Chris YouTube channel is focused on educational and entertaining "How To" woodworking videos using just hand tools. My DIY content covers a wide range of projects and plans from tables and chairs to foot powered machines, bows, arrows, crossbows and other related bushcraft videos as well as tool eduction. I am a maker and have a passion to share my knowledge with others.
Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
I've been through many tools in that time and I rarely buy new. So many begin this hobby with a zillion tools but never use them. They wait about two years and sell. The best thing is the price but I also like the fact when she looks for my list items she finds so many other things that were future list items. I won't bore with good deal stories but I have many.
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
Woodworking is a fun hobby, but can be expensive as well. With all the power tools, hand tools, shop setups and, of course, the wood, many people are turned off to woodworking because of the impact on their wallets. That doesn’t have to be the case though. With a little pre-planning and inside knowledge, you can set up a basic wood shop and start making your own items without breaking the bank.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
One of the most heavily used tools in your shop will be your table saw. It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs. Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
Jon Peters Art & Home is a show about DIY woodworking and other home-related topics. Jon keeps it interactive by encouraging viewers to send their project pictures to him so that he can have a look at them. And if you like some drama with your woodworking videos, Jon does occasionally record videos of him freaking out about things like cheap Chinese wood.
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt. Unfortunately, that ended up with the guy we hired stealing from us…..uggggh. When will we ever learn to not be so trusting?! Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!! Sad. Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.
While I am admittedly still new to the wonderful world of woodworking, I can't help but feel that one of the contributing issues/factors responsible for my prolonged progress in starting/finishing projects is how I've become accustomed (more like "trained") - fortunately or unfortunately, depending how you look at it - to work within a financial budget.
For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
Being able to create and build a masterpiece from pieces of wood is more than a hobby -it’s a craft. Buying all the tools and supplies you need can start to add up to some serious money. But there are ways to enjoy building with wood without breaking your budget. Here’s a few woodworking tips that may get you started saving money and still being creative.
That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
Then there are the “practical” woodworkers that enjoy weekend projects and things that don’t require a ton of expensive tools, time, and expertise (HELLO, THAT’S ME). I will be in the latter category. Sure, you can invest in hand tools, but in the words of one of my favorite internet sensations, “ain’t nobody got time fo that.” Let’s be practical here.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
My name is Marc Spagnuolo and welcome to my channel. I am a podcaster, video producer, author, and woodworking enthusiast. I have contributed articles and video content to FineWoodworking.com, Popular Woodworking Magazine and WOOD Magazine. Producing the Wood Whisperer is a great way for me to combine four of my passions: woodworking, technology, education, and humor. I believe that even the most complicated woodworking project is just a series of steps. My goal with this channel is to show you the tools and techniques you need to perform those steps.